User manual PANASONIC KX-TC190W

[. . . ] 8 Numbering Plan Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Numbering Plan Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 1. 1 1. 2 1. 2. 1 1. 2. 2 1. 2. 3 2 Installing in the KX-TDA50 PBX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Names and Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] It is possible, at one location in the network, to program the address translation table that contains information for the entire network. The completed address translation table can then be distributed across the network, so that all the cards share the same information (see "4. 2. 6 Downloading the Address Translation Table from the VoIP Gateway Card", and "Uploading Address Translation Table to the VoIP Gateway Card" in "4. 3 Programming the VoIP Gateway Card in the Chicago Office"). The procedure below demonstrates the process of programming the address translation table necessary for VoIP communications between the Los Angeles and Chicago offices. The specific setting values are based on the table under "PBX Connection Information" in "1. 2. 2 Numbering Plan Example". Click 1. 6 DN2IP (Dialed Number to IP Address Translation) in the main menu. 2. Click 1. 6. 1 GW Entry. *1 IP address-to-telephone number translation can also be handled by using an H. 323 Gatekeeper device. To configure Gatekeeper devices, refer to the manufacturer's documentation. This manual focuses on the method using the VoIP Gateway Card's internal address translation capabilities. 34 Getting Started 4. 2 Programming the VoIP Gateway Card in the Los Angeles Office 3. Do the following to configure the gateway entry for the Los Angeles office: a. box, type 0. A gateway entry for the card will be created with this numbering. b. In the Comment box, type Los Angeles (a unique identifier of the card in the VoIP network). c. Start Internet Explorer from the Start menu. In the Address box of Internet Explorer, type http://200. 45. 11. 35 (the new IP address of the card). 4. Press the ENTER key on the keyboard. If you can log in, then the card has been successfully programmed. After you have confirmed that the card has been successfully programmed, it is strongly recommended that you download the configuration data from the card and save it on your PC for backup and archive purposes. The procedure for downloading the configuration data is provided in "2. 4. 2 Download of Configuration Data" of the VoIP Gateway Card Programming Guide. Getting Started 39 4. 3 Programming the VoIP Gateway Card in the Chicago Office 4. 3 Programming the VoIP Gateway Card in the Chicago Office This section details the procedure to program the VoIP Gateway Card in the Chicago office, which for the most part is a duplication of that for the Los Angeles office. For general information that is not discussed here, refer to the relevant sections in "4. 2 Programming the VoIP Gateway Card in the Los Angeles Office". There are differences in the procedure where distinct setting values are required for parameters that are dependent on the specific network configuration of the Chicago office. Also, the address translation table does not need to be programmed, because the one downloaded from the card in the Los Angeles office already contains the information for the entire network. You can simply upload the address translation table from the Los Angeles office, and the cards can communicate with each other on the network. Starting the IP-GW4 Maintenance Utility 1. Start Internet Explorer from the Start menu. In the Address box of Internet Explorer, type http://192. 168. 1. 200 (default IP address of the card). [. . . ] A unique IP address must be assigned to each card. Identifies the IP address of the primary gateway (typically a router or similar device) 199. 176. 64. 1 that exchanges IP packets with the other gateways on the VoIP network. Default Gateway Address 200. 45. 11. 1 Subnet Mask Address Defines which digits of an IP address are used for the network address and the host address at each network location. A card IP 255. 255. 255. 0 255. 255. 255. 0 address must fall within the same subnet as that of the default gateway (e. g. , router) that is connected to the card. PBX Numbering Information The following table contains "VoIP Gateway Trunk (CO Line) Access Number", instead of "PBX Code" and "TIE Line Access Number" as used in the PBX code method. Los Angeles Office VoIP Gateway Trunk (CO Line) Access Number PSTN Trunk (CO Line) Number Extension Number Fax Extension Number Chicago Office Description 802 803 An access number to seize a VoIP gateway trunk (CO line). 92 93 An access number to seize a local PSTN trunk (CO line). [. . . ]