User manual PANASONIC KX-TC900DW

[. . . ] [FLASH/CALL WAIT] (3-D) PQKE10364Z1 Microphone (2-A) Charge Contacts (4-A) [VOICE ENHANCER] and Indicator (2-A) CHARGE Indicator (1-C) [HANDSET LOCATOR] (3-B) For extra orders, call 1-800-332-5368. 1-C Settings 1 Connect as shown. Fasten the AC adaptor cord. Hooks Single-Line Telephone Jack (RJ11C) Telephone Line Cord Power Outlet (AC 120 V, 60 Hz) AC Adaptor 2 Insert the battery (1), and press it down until it snaps into the compartment (2). Close the cover. 1 2 USE ONLY WITH Panasonic AC ADAPTOR PQLV19 (Order No. The AC adaptor must remain connected at all times. [. . . ] To turn the ringer ON, press [M] or [L]. You can select the ringer volume while an external call is being received. Press [M] or [L] while the unit is just ringing. To set to OFF, press and hold [M] until 2 beeps sound. For the best operating performance, see section 4-F. To redial the last number dialed Press [ ] or [SP-PHONE], then press [REDIAL]. To adjust the receiver/speaker volume while talking 3 levels (HIGH, MEDIUM and LOW) are available for the receiver and 6 levels for the speaker. If you try to increase/decrease volume when it is at the maximum/minimum level, 3 beeps will sound. Selecting the ringer tone Make sure the unit is not being used and the handset is lifted off the base unit. Press [M] or [L], then press [1] (preset) to [6] within 10 seconds. If noise interferes with the conversation Have the unit select a clearer channel by doing one of the following: Press [ ] (Channel) if talking using [ ], or press [SP-PHONE] (Channel) if talking using [SP-PHONE]. OR Walk closer to the base unit. Lighted handset keypad The handset dialing buttons will light when you press a button or lift the handset off the base unit. The light will go out after a few seconds. For assistance, please call: 1-800-211-PANA(7262) 3 Special Features 4 Things You Should Know 3-A Automatic Security Code Setting Each time you place the handset on the base unit, the unit automatically selects one of a million security codes. These codes help prevent the unauthorized use of your telephone line by another cordless telephone user. 4-A Battery Recharge When the RECHARGE indicator flashes or the unit beeps intermittently, place the handset on the base unit for about 6 hours to recharge the battery. If you DO NOT recharge the handset battery for more than 15 minutes, the RECHARGE indicator will continue to flash. Battery replacement: If you cleaned the charge contacts and fully charged the battery, but after a few telephone calls, the RECHARGE indicator flashes, the battery needs to be replaced. If you use the handset near another cordless phone, noise may be heard. Move away from the other cordless phone and closer to your base unit. 3 Tuck the telephone line cord inside the wall mounting adaptor, then push the adaptor in the direction of the arrows (1 and 2). The word "UP WALL" should face upward. 4-G Specifications 2 1 Base unit Power Supply: Power Consumption: 4 Connect the telephone line cord. Mount the unit, then slide down. Raise the antenna. AC Adaptor (120 V AC, 60 Hz) Standby: Approx. 3. 9 W Frequency: 2. 402 GHz­2. 480 GHz Dimensions (H k W k D): Approx. 104 mm k 148 mm k 173 mm (4 3/32q k 5 27/32q k 6 13/16q) Mass (Weight): Approx. 310 g (0. 68 lb. ) Handset Power Supply: Ni-MH battery (2. 4 V, 1, 500 mAh) Frequency: 2. 402 GHz­2. 480 GHz Dimensions (H k W k D): Approx. 246 mm k 52 mm k 41 mm (9 11/16q k 2 1/16q k 1 5/8q) Mass (Weight): Approx. 210 g (0. 46 lb. ) Security Codes: 1, 000, 000 Dialing Mode: Tone (DTMF)/Pulse Operating Environment: 5°C­40°C Specifications are subject to change without notice. 5 To charge the handset battery: Place the handset on the base unit. The CHARGE indicator lights and the unit beeps once. Energy Star: As an ENERGY STARR Partner, Panasonic has determined that this product meets the ENERGY STAR guidelines for energy efficiency. registered mark. For assistance, please call: 1-800-211-PANA(7262) Things You Should Know 4-H Troubleshooting Problem The unit does not work. Cause & Remedy Check the settings (1-C). Clean the charge contacts and charge again (4-A). [. . . ] ], [L], [M] Indicador RECHARGE [ ] [SP-PHONE] [OFF] Para seleccionar el volumen del timbre Asegúrese de que la unidad no se está usando y de que la unidad portátil se ha levantado de la unidad base. Para seleccionar ALTO (preajustado), MEDIO o BAJO, presione [M] o [L] para checar el volumen actual, y luego presione [L] o [M] antes de que pasen 10 segundos para seleccionar el volumen. El volumen cambiará y sonará. Para apagar el timbre, mantenga presionado [M] hasta que suenen 2 pitidos. [. . . ]