User manual PANASONIC KX-TCD420

[. . . ] Digital Cordless Answering System Preparation Operating Instructions Contents Preparation Before Initial Use . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Information . . . . . . . . . . . . . . . . . . 3 Setting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Model No. KX-TCD420E Cordless Telephone Cordless Telephone Using the Telephone . . . . . . . . . . . . . . . . . . . [. . . ] Handset must be registered within 1 minute after pressing PAGE button. If over 1 minute, press then start over again. Charge the optional handset batteries for 7 hours before initial use. 1 Press MENU. 2 Search/Select "SETTING HS". 3 Search/Select "REGISTRATION". "REGISTER HS" 4 Press RIGHT. *1 5 Press and hold on the Base Unit (for about 10 seconds) until the green indicator flashes. If all registered handsets start ringing (Paging), press to stop paging then start over again. 6 Search/Select desired base unit number available to register the handset. 7 4-digit Base Unit PIN after "BS PIN" is displayed. 8 Press OK. Factory preset 0000 When a handset is registered successfully, a confirmation tone sounds and " " icon lights. any time. · To exit the operation, press *1 If a handset has been already registered to 4 base units, "MEMORY FULL" is displayed. 28 Multi-unit User Operation Cancelling a Base Unit You can cancel any base unit that your handset is registered to. 1 Press MENU. 2 Search/Select "SETTING HS". 3 Search/Select "REGISTRATION". 4 Search/Select "CANCEL BS". 5 4-digit Handset PIN 6 Factory preset 0000 7 Press RIGHT. 8 Search/Select "YES" or "NO". Search/Select desired base unit number to cancel. *1 Cordless Telephone Cancelling a Handset Each handset can cancel itself or another handset. 1 Press MENU. 2 Search/Select "SETTING BS". "INPUT CODE" 3 7 4 4-digit Base Unit PIN Factory preset 0000 5 Handset Number Select desired handset. *2 6 Press OK. Please wait until "SETTING BS" is displayed. any time. · To exit the operation, press *1 The selected base unit number flashes. *2 The selected handset number flashes. Helpline Tel. No. 01289 8333 29 Multi-unit User Operation Before programming, please follow steps 1 to 4. 1 Press MENU. 2 Search/Select "SETTING BS". "INPUT CODE" 3 1 4 4-digit Base Unit PIN Factory preset 0000 Ringer Mode Selection; Setting the All Handsets Mode 5 1 "All handsets" mode. 6 Press OK. Setting the Selected Handsets Mode 5 2 "Selected handsets" mode. 6 Handset Numbers*1 7 Press desired handset numbers. Press OK. Setting the Selected then All Handsets Mode The specific handset(s) will ring for a selected number of rings. If not answered, all handsets will ring. 5 3 "Selected then all handsets" mode. 6 Handset Numbers*1 7 Press desired handset numbers. Press RIGHT. 8 Number of Rings*2 Select how many times it rings. (up to 6 rings) 9 Press OK. any time. · To exit the operation, press · The factory preset is in shade. *2 Press dialling button 1 through 6 to enter the number of rings. 30 Multi-unit User Operation : Base Unit Selection When Automatic Base Unit Access is selected, if you move outside of the radio range of the current base unit, the handset automatically searches for other registered bases. When a specified base unit is selected, the handset will access that base unit only. Calls (both incoming and outgoing) can be conducted only via the selected base unit, even if the radio cells overlap with neighbouring base units. 1 Press MENU. 2 Search/Select "SETTING HS". 3 Search/Select "SELECT BS". 4 Search/Select "AUTO" or specific base unit number. Cordless Telephone · To exit the operation, press any time. Operating Additional Base Units: You can register and operate your handset with up to 4 base units. If the individual bases are linked to the same telephone line then you can extend the operating range of the system by positioning the bases so that the two radio cells overlap. If the handset is set to AUTO base selection, then in standby mode the handset will automatically swap to the second base if the range on the first base is exceeded. It is not possible to transfer calls between bases (only between handsets linked to the same base unit). 1 2 4 3 5 Radio Cell Eg. Additional handsets (KX-A142E) registered with 2 base units. Note: Calls are disconnected when the handset moves from one radio cell to another. Helpline Tel. No. 01289 8333 31 Intercom Intercom between Handsets You can use your handsets as a 2-way intercom. For example, when Handset 1 calls Handset 2. To hang up, press <Handset 1> . 1 INT ( on the display) Press INTERCOM. 2 2 Press desired Handset Number. <Handset 2> 3 Press TALK. *1 · Intercom calls can be conducted within the radio cell of the current base unit, but not with units in neighbouring radio areas. Transferring a Call to Another Handset/Conference Call Intercom can be used during a call to transfer an external call between handsets that are registered to the same base unit. For example, when handset 1 transfers a call to Handset 2. To hang up, press . <Handset 1> (During a call) 1 INT ( on the display) 2 2 Press desired Handset Number. *2 4 3 *3 Press INTERCOM. <Handset 2> 3 Press TALK. *1 *1 You can also press any dialling button, INTERCOM, t or x. [. . . ] 40 Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Useful Information Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 45 Guarantee CONDITIONS OF GUARANTEE This guarantee is in addition to and does not in any way affect any statutory or other rights of consumer purchasers. If within the applicable guarantee period, the appliance proves to be defective by reason of faulty design, workmanship or materials, we undertake subject to the following conditions to have the defective appliance (or any part or parts there of) repaired or replaced free of charge. [. . . ]