User manual PANASONIC KX-TCD445

[. . . ] Operating Instructions Digital Cordless Phone Model No. KX-TCD440E KX-TCD445E Digital Cordless Answering System Model No. This unit is Caller ID compatible. To display the caller's phone number, you must subscribe to Caller ID service. Charge the batteries for about 7 hours before initial use. Please read these Operating Instructions before using the unit and save them for future reference. Table of Contents Preparation Accessory information . 9 Useful Information Troubleshooting . [. . . ] Press {ih}. Adjusting ringer volume 4 levels (high to off) are available. {7} {*} Cancel a handset*1 Time and date *1 If you cancel a handset, the base unit will "forget" the handset registration. 1 Press {j}. 2 Press {v} repeatedly to display "SETTING BS", then press {>}. 3 Press {2} 2 times. 4 Select the desired setting by pressing {1} for low, {2} for medium, {3} for high or {0} for off. 5 Press {>}, then press {ih}. 2 Press {v} repeatedly to display "SETTING BS", then press {>}. 3 Press {3}. 22 Helpline Tel. 01289 8333 Useful Telephone Settings 4 Enter "0000" (default base unit PIN). L If you changed PIN, enter it (page 22). L To select a different memory location, press {>} repeatedly and enter a number. 5 Press {3}. 6 Select the desired setting by pressing {1} for 3 seconds or {2} for 5 seconds. 8 Press {>}. 9 Press {ih}. Turning on/off call restriction 7 Press {>}, then press {ih}. Setting call restriction You can restrict selected handsets from dialling certain phone numbers. You can assign up to 10 phone numbers (memory locations 1­10) to be restricted per handset. If a restricted number is dialled, the call will not be connected and the restricted number will flash on the display. For example, storing an area code will prevent a handset from dialling a long distance call. 1 Press {j}. 2 Press {v} repeatedly to display "SETTING BS", then press {>}. 3 Press {6}. 4 Enter "0000" (default base unit PIN). L If you changed PIN, enter it (page 22). Flashing numbers indicate call restriction is on; non-flashing numbers indicate call restriction is off. 1 Press {j}. 2 Press {v} repeatedly to display "SETTING BS", then press {>}. 5 Press the desired handset numbers to turn on/off. 3 Press {6}. 4 Enter "0000" (default base unit PIN). L If you changed PIN, enter it (page 22). L All the registered handset numbers will be displayed. L Flashing numbers indicate call restriction is turned on for the corresponding handset. 6 Press {>}, then press {ih}. Cancelling a restricted number 1 Press {j}. 2 Press {v} repeatedly to display "SETTING BS", then press {>}. 3 Press {6}. 4 Enter "0000" (default base unit PIN). L If you changed PIN, enter it (page 22). 5 Press the desired handset numbers. L The selected handset numbers will flash. L To cancel a selected handset number, press the number again. [. . . ] The appliance should be returned together with this guarantee and proof of date of purchase promptly on being found defective at the purchaser's risk and expense to the authorised dealer from whom the appliance was purchased or to the nearest authorised dealer. All enquires must be through such dealers. This guarantee shall not apply to damage caused through fire, accident, lightning, misuse, wear and tear, neglect, incorrect adjustment or repair, to damage caused through installation, adaption, modification or use in an improper manner or inconsistent with the technical and/or safety standards required in the country where this appliance is used, or to damage occurred during transit to or from the purchaser. If at any time during the guarantee period any part or parts of the appliance are replaced with a part or parts not supplied or approved by us or of an objective quality safe and suitable for the appliance, or the appliance has been dismantled or repaired by any person not authorised by us, we shall have the right to terminate this guarantee in whole or in part immediately without further notice. [. . . ]