User manual PANASONIC KX-TCD820FX

[. . . ] TCD820FX(e-e). book Page 1 Tuesday, September 13, 2005 9:10 AM Operating Instructions Digital Cordless Answering System Model No. KX-TCD820FX This unit is compatible with Caller ID and SMS. To use these features, you must subscribe to the appropriate service of your service provider. Charge the batteries for about 7 hours before initial use. Please read these operating instructions before using the unit and save them for future reference. (For Czech and Slovakia) This cordless telephone is possible to use according to General licence No. : GL23/R/2001 (for Czech), VPR-7/2001 (for Slovakia). TCD820FX(e-e). book Page 2 Tuesday, September 13, 2005 9:10 AM Introduction Introduction Thank you for purchasing a new Panasonic digital cordless phone. [. . . ] Storing area codes here will prevent the restricted handsets from dialling any phone number in that area code. You can allow a call restricted number to be dialled if it stored as an emergency number. 3 4 5 6 "Call Options" i # "Emergency No. " i # Select a memory location. i # i {ih} L To erase an emergency number, press and hold {C/T}. 1 " (centre of joystick) i n i # 2 Enter the base unit PIN (default: "0000"). Other options Changing the base unit PIN (Personal Identification Number) For security, the base unit PIN must be entered when changing certain settings. Important: L If you change the PIN, please make note of your new PIN. The unit will not reveal the PIN to you. If you forget your PIN, consult your nearest Panasonic service centre. 3 "Call Options" i # 4 "Call Restrict" i # 5 Set which handsets will be restricted by selecting the handset then pressing S. L Restricted handsets have a "Q" next to them. L To turn call restriction off for a handset, select the restricted handset, then press S. 6# 7 Select a memory location. i # 8 Enter the phone number or area code to be restricted (8 digits max. ). i # i {ih} L To erase a restricted number, press {C/T}. 1 " (centre of joystick) i n i # 2 Enter the base unit PIN (default: "0000"). 3 "Other Options" i # 4 "Base Unit PIN" i # 5 Enter the new 4-digit base unit PIN. i # i {ih} 40 TCD820FX(e-e). book Page 41 Tuesday, September 13, 2005 9:10 AM n Base Unit Settings Changing the unit's region setting/Resetting the base unit 1 " (centre of joystick) i n i # 2 Enter the base unit PIN (default: "0000"). ­ Number of times the unit redials when using the auto redial feature (page 16) ­ Language used for answering system announcements L After resetting the base unit, w will flash on the handset momentarily. The handset can be used once w stops flashing. 3 "Other Options" i # 4 "Reset Base" i # 5 Select the desired country. i # "EG"=countries except Czech and Slovakia "PD"*1 "CZ"=Czech "SK"=Slovakia *1 Do not select "PD". 6 "Yes" i # i {ih} Note: L The following items will be deleted or reset to their default settings: ­ Settings listed on page 37, 50, 55 ­ All SMS messages ­ Caller list L The following items will be retained: ­ Date and time ­ Shared phonebook entries ­ Repeater mode ­ Recordings, including your greeting message, caller messages, voice memos, audible call announcements, and recorded conversations L If you select the desired country in step 5, the following default settings will be changed for the selected country's default settings: ­ Message centre 1 and 2 (page 50) ­ Recall time (page 37) ­ Emergency number (page 37) ­ Language (page 26) ­ LetterWise (page 26) ­ ARS settings (page 37) ­ SMS on/off (page 50) 41 TCD820FX(e-e). book Page 42 Tuesday, September 13, 2005 9:10 AM o Infrared Copying saved data via infrared interface You can copy stored phonebook entries as well as picture and ringtone data between other compatible Panasonic handsets, as well as compatible GSM phones that feature an infrared interface. Infrared data transmission between the handset and other devices except GSM phones cannot be guaranteed. See page 69 if you have difficulty using the features in this section. Example: Handset 1 is sending its data to handset 2 (receiver) Pictures larger than about 50 KB cannot be displayed. L Disconnect the USB cable from the handset when you copy data via infrared interface. L You cannot send or receive data via infrared interface when the battery strength is low. L Only characters shown in the character entry tables (page 61) can be used for phonebook entry names or file names of pictures or melodies. Note: L Certain GSM phones are not compatible with this feature. Infrared port Copying phonebook entries Only names and phone numbers can be copied via infrared interface. 1 Handset 1 and Handset 2 (receiver): " (centre of joystick) i o i # 2 Handset 1: "Send" i # Handset 2 (receiver): "Receive" i # 3 Handset 1: "Phonebook" i # Caution: L This device contains a low power level Class 1 laser product (Infrared LED), which will not normally harm the eyes. Though invisible to the eye, do not point the infrared beam at anyone's eye. [. . . ] 6. 8 W Operating conditions: 5 °C­40 °C, 20 %­80 % relative air humidity (dry) Dimensions: Base unit: Approx. 54 mm × 110 mm × 168 mm Handset: Approx. 158 mm × 48 mm × 34 mm Mass (weight): Base unit: Approx. 154 g Note: L Specifications are subject to change. L The illustrations used in these operating instructions may differ slightly from the actual product. [. . . ]