User manual PANASONIC KX-TCD961

[. . . ] KX-TCD961E-Chap. 1(1) 99. 9. 27 6:31 PM Page 1 Digital Cordless Answering System Model No. KX-TCD961EB Operating Instructions ANSW ER O N INT' C PROG OK RDL GREE TING ERAS E 1 GH I AB C 2 5 DE F 3 6 9 SELE CT 4 7 JK L MNO PQRS TU V 8 0 WXYZ PWR RCL PLEASE READ BEFORE USE AND SAVE. Charge the batteries for about 4 hours before initial use. This equipment is not designed for making emergency telephony calls when the power fails. Alternative arrangements should be made for access to emergency services. KX-TCD961EB. 1(2~22) 99. 9. 27 7:37 PM Page 2 Important Information Do not connect the AC adaptor to any AC outlet other than the standard AC 230­240 V, 50 Hz. · Outlet voltage DC1 8 V, 500 mA Outlet voltage DC2 9 V, 200 mA · The apparatus is approved for use with the KX-TCA11E power supply. This apparatus has been approved for the use of the following facilities: 1) Storage of telephone numbers for retrieval by a predetermined code 2) Last number redial 3) Simple telephone facility 4) PBX earth register recall (option) PBX timed break register recall 5) MF signalling 6) LD signalling 7) Pause 8) Intercom 9) Call prohibition 10) Call restriction 11) Direct call 12) Intercom between handsets 13) Transferring a call from one handset to another 14) Conference 15) Setting the call waiting tone 16) Accessing the base unit 17) Answering & Recording Machine 18) Recording and playback of ICM 19) DTMF tone remote control system 20) Memo recording feature 21) Monitoring a telephone call 22) LCD call-counter: to indicate received messages 23) Vox facility: detection of caller's hanging up 24) Selecting the number of rings 1­7/AUTO 25) Auto disconnect 26) Total recording time (including the greeting message) is about 14 minutes 27) Security code for remote operation Any other usage will invalidate the approval of the apparatus if as a result, it then ceases to conform to the standards against which approval was granted. [. . . ] The factory preset is the length of the call. 1 2 Press PROG . Press G or F until "F32" is displayed, then press OK . · The current setting is displayed. 1: Length of the call 0: Dialled phone number Ex. Length of the call is selected. During a conversation, the display will be as follows. Length of the call (Ex: 1 h. , 30 min. , 40 sec. ) 88880 i - 30 - 40 Dialled phone number (Ex: 123-456-7890) F32U i 3 Press G or F to select the desired setting. · You can also press 0 or 1 to select the setting. i234567890 4 Press PROG . · A confirmation tone sounds and the display will return to the stand-by mode. 36 KX-TCD961EB. 3(30~37) 99. 9. 27 7:34 PM Page 37 Clearing the Settings in Memory This function enables the handset or base unit to clear the following settings at one time. They will return to their initial settings. On the handset Function Base unit access Key tones Handset ringer volume Handset ringer pattern Call waiting tone Range warning alarm Battery low alarm Stand-by mode display Talk mode display Call prohibition Direct call mode Direct call number Handset password Handset receiver volume Redial memory Initial setting Automatic base unit access ON 3 (MEDIUM) 1 ON OFF ON Base unit number Length of the call OFF OFF Clear 0000 MEDIUM All clear On the base unit Function Bell selection Dialling mode Earth/time break recall Pause timing Call restricted handset(s) Call restriction number(s) Base unit password Base unit ringer volume Base unit ringer pattern Initial setting All handsets Tone Time break recall 3 seconds All clear All clear 0000 2 (MEDIUM) 1 Chapter 3 1 2 3 Press PROG then INT . 31). Cordless Telephone (Advanced Operations) 1 2 3 Press PROG . Press G or F until "F0" is displayed, then press OK . · A confirmation tone sounds and the display will return to the stand-by mode. -----------4 Press PROG . · A confirmation tone sounds and the display will return to the stand-by mode. 37 KX-TCD961EB. 4(38~46) 99. 9. 27 7:33 PM Page 38 Automatic Answering Operation When the unit answers a call, a greeting message is played and the caller's message is recorded. · The total recording time (including the greeting message) is approximately 15 minutes. · A maximum of 64 messages (including the greeting message) can be recorded. Setting the Unit to Answer Calls Press ANSWER ON to turn on the answering system. · The indicator lights and "Answer set" is heard. · The unit will announce the remaining recording time if it is less than 5 minutes. · If you hear "Memory is full" and the indicator flashes rapidly, erase some or all of the messages (p. 40). ANSWER ON Button and Indicator · If you do not want the unit to answer calls, press ANSWER ON again to turn off the answering system. The indicator light goes out and "Answer off" is heard. · You can also turn on the answering system remotely using any other phone (p. 44). Monitoring incoming calls While a call is being recorded, you can monitor it through the speaker. The unit stops recording. 38 KX-TCD961EB. 4(38~46) 99. 9. 27 7:33 PM Page 39 Listening to Messages You can see the total number of recorded messages on the base unit display. [. . . ] Advantages of DECT Excellent voice quality: Through sampling of digital signals DECT units obtain nearly noiseless transmission. High grade taping security: Based on digital transmission, DECT conversations are well protected against unapproved monitoring. Multi-Handset operation: To operate several handsets at the base unit, no cable installation is required. Interlink: Intercom conversation can be held free of charge between the registered handsets. [. . . ]