User manual PANASONIC KX-TD1232SL

[. . . ] Digital Super Hybrid System U M SER ANUAL Please read this manual before using the Digital Super Hybrid System. MODEL KX-TD816SL / KX-TD1232SL Thank you for purchasing the Panasonic Telephone Systems. System Components Model No. Service Unit KX-TD816SL KX-TD1232SL KX-T7230SL KX-T7235SL KX-T7250SL KX-T7240SL Description Digital Super Hybrid System (Main Unit) Digital Super Hybrid System (Main Unit) Digital proprietary telephone with display Digital proprietary telephone with large display Digital proprietary telephone with monitor Digital DSS Console Telephone Optional Equipment User-supplied Equipment Single Line Telephone NOTICE: In this User Manual, the suffix "SL" of each model number is omitted. 2 Attention · If there is any trouble, unplug the extension line and connect a known working phone. If the known working phone operates properly, have the defective phone repaired by one of the specified Panasonic Factory Service Centers. If the known working phone does not operate properly, check the Digital Super Hybrid System and the Internal extension wiring. [. . . ] However the SLT can answer the call. DPT Features 4-113 P 4. 2 DPT Features · When the SLT is in use, the display and the indicators of the PT will show in the same way as if the PT is in use. · If you go off-hook while your paralleled telephone is in use, the call will switch over to your telephone, and vice versa. · "XDP*" feature is available. · With the KX-T7235, you can execute this feature with the display operation. Programming References · System Programming -- Installation Manual [100] Flexible Numbering, Parallel telephone mode Feature References Alternate Calling -- Ring/Voice EXtra Device Port (XDP) ( see Installation Manual) Handsfree Answerback System Feature Access Menu -- Paralleled Telephone Connection (4. 4/Special Display Features) * XDP (eXtra Device Port) expands the number of telephones available in the system by allowing an extension port to contain two telephones. 4-114 DPT Features 4. 2 DPT Features P Pickup Dialing (Hot Line) Allows you to make an outgoing call by lifting the handset. Programming the phone number 1 1. Lift the handset or press the SP-PHONE/MONITOR button. 2 2. Dial the feature number (74) and 2. 7 3 4 2 3. · You hear a confirmation tone and then a dial tone. phone number and # 4. Hang up or press the SP-PHONE/MONITOR button. 4 Setting 1 1. Lift the handset or press the SP-PHONE/MONITOR button. 2 7 3 4 1 2. · You hear a confirmation tone and then a dial tone. Hang up or press the SP-PHONE/MONITOR button. Cancelling 1 1. Lift the handset or press the SP-PHONE/MONITOR button. 2 7 3 4 0 2. · You hear a confirmation tone and then a dial tone. Hang up or press the SP-PHONE/MONITOR button. DPT Features 4-115 P Dialing 1 4. 2 DPT Features 1. Lift the handset or press the SP-PHONE/MONITOR button. · Wait for the answer and talk. Conditions · This feature does not work if you answer an incoming call or retrieve a call on hold. · Up to sixteen digits, consisting of "0 through 9" and " , " can be stored. · During the waiting time after going off-hook, you can dial another party, overriding this feature. The waiting time is programmable. Programming References · System Programming -- Installation Manual [100] Flexible Numbering, Pickup dialing program [204] Pickup Dial Waiting Time 4-116 DPT Features 4. 2 DPT Features P Predial Preparation (for KX-T7230 and KX-T7235 only) Allows you to confirm the phone number with the LCD before the line is connected. · The display shows the dialed telephone number. <Example> phone number 012345678 If you want to change the current entry; 2. · By pressing , the number at the right-hand edge is deleted. [. . . ] · The duration time display is shown only when you make or receive a CO call. Count starting time for outgoing calls can be programmed as desired. · When you confirm key programming, be sure to press a button while on-hook. If the "Full One-Touch Dialing" feature is set, dialing mode will start when pressing PF (Programmable Feature), DSS, SAVE or REDIAL button. Appendix 8-13 8 Feature Number List Appendix Numbers listed below are the initial factory setting (default value). [. . . ]