User manual PANASONIC KX-TG2267B

[. . . ] 2. 4GHz Digital Cordless Phone Preparation Operating Instructions Model No. KX-TG2267B KX-TG2267S Pulse-or-tone dialing capability Basic Operation Advanced Operation Useful Information KX-TG2267B 2 LINE Caller ID Compatible PLEASE READ BEFORE USE AND SAVE. Charge the battery for about 15 hours before initial use. Panasonic World Wide Web address: http://www. panasonic. com for customers in the USA or Puerto Rico Thank you for purchasing your new Panasonic cordless telephone. Please read IMPORTANT SAFETY INSTRUCTIONS on page 65 before use. Read and understand all instructions. Caller ID and Call Waiting Service and Voice Mail Service, where available, are telephone company services. After subscribing to Caller ID, this phone will display a caller's name and phone number. [. . . ] To use this feature, you must first store your access number. Storing a Voice Mail Access Number Make sure the unit is not being used and the handset is lifted off the base unit. Line Buttons , , (OFF) VM (Voice mail) Indicator (HOLD/FUNCTION/CLEAR) (FLASH/CALL!WAIT/VOICE!MAIL) 1 2 3 44 Press (HOLD/FUNCTION/CLEAR). Scroll to "Program" by pressing Ö or Ñ. Ringer tone HProgram -------------- 4 5 6 7 8 9 Scroll to "Save VM acces#" by pressing Ö or Ñ. Press á. Set flash time HSave VM acces# VM tone detect Press Ö (Line 1) or Ñ (Line 2) to select the line. Save VM access# G=Line1 F=Line2 Enter your access number, up to 32 digits. ·You may enter pauses*. ·Each time you press (HOLD/FUNCTION/CLEAR), a digits is erased. To erase all digits, press and hold (HOLD/FUNCTION/CLEAR). 1234567PPP890 IH G=Next Press Ö (Next key). ·If you want to edit the entered number, press Ñ (Edit key) and return to step 7. 1234567PPP890 F=Edit H=Save Press á (Save key). ·A beep sounds. ·To program the other line, start again from step 4. ·To exit the programming mode, press (OFF). 1234567PPP890 Advanced Operation Save VM access# ·You can exit the programming mode any time by pressing (OFF). *For quick access to your voice mail box by using (FLASH/CALL!WAIT/VOICE!MAIL), you may add pauses between your voice mail box access number and your mail box password in step 7. 1-222-333-4444 PPPP 8888 Your mail box password Pauses Pressing (REDIAL/PAUSE) once creates a 3. 5 seconds delay and counts as one digit. The delay time depends on a telephone company. Your voice mail box access number To erase a stored number Repeat steps 1 through 6 \ Press and hold (HOLD/FUNCTION/CLEAR) until all of the digits are erased \ Ö (Next key) \ á (Save key). ·A beep sounds. For assistance, please call: 1-800-211-PANA(7262) 45 Voice Mail Service Setting the Voice Mail (VM) Tone Detection Your telephone company sends special signals (Voice mail tones) to activate the VM indicator. If you hear a series of dial tones followed by a continuous dial tone, this is indication that a new message was recorded. Your phone comes set to detect these tones (set to "On"). Minutes after you hang up or after the phone stops ringing, your unit will seize the phone line and check if a message has been recorded. If a new message was recorded at your telephone company, "Voice mail" will be displayed on the handset and the base unit VM indicator will flash. Set this programming to "Off" when: --you do not subscribe to a voice mail service, --your telephone company does not send a series of tones, followed by a continuous tone, or --your phone is connected to a business or office telephone system (PBX). Please refer to below to set this programming to OFF. If you are not sure which setting is required, consult your local telephone company or contact Panasonic Customer Call Center. Make sure the unit is not being used and the handset is lifted off the base unit. 1 2 3 4 5 6 7 46 Press (HOLD/FUNCTION/CLEAR). Scroll to "Program" by pressing Ö or Ñ, and press á. Scroll to "VM tone detect" by pressing Ö or Ñ. Save VM acces# HVM tone detect Set line mode Press á. VM tone detect G=Line1 F=Line2 Press Ö (Line 1) or Ñ (Line 2) to select the line. ·The line's current setting will be displayed. VM tone detect Line1:On GF H=Save Select "Off" or "On" by pressing Ö or Ñ. VM tone detect Line1:Off Press á (Save key). ·A beep sounds. [. . . ] 23, 24 Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24, 27 MUTE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 N Noise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 P PAUSE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]