User manual PANASONIC KX-TG2302

[. . . ] 2. 4GHz Digital Cordless Phone Operating Instructions Model No. KX-TG2302 Pulse-or-tone dialing capability PLEASE READ BEFORE USE AND SAVE. Charge the battery for 6 hours before initial use. 1 2 3 4 5 Panasonic World Wide Web address: http://www. panasonic. com for customers in the USA or Puerto Rico Contents by Section Getting Started Making/Answering Calls Special Features Things You Should Know Guía rápida Attach your purchase receipt here. For product service · Visit our website: http://www. panasonic. com/support · Contact us via the web at: http://www. panasonic. com/contactinfo · Call us at: 1-800-211-PANA(7262) or 1-800-833-9626 When you ship the product · Carefully pack your unit, preferably in the original carton. · Attach a letter, detailing the symptom, to the outside of the carton. Symptom · Send the unit to an authorized servicenter, prepaid and adequately insured. · Do not send your unit to the Panasonic Consumer Electronics Company listed below or to executive or regional sales offices. [. . . ] You need to re-register the handset to the base unit. · Have both the handset and base unit nearby during registration. · Follow steps 1 and 2 listed below. You have about 1 minute to complete them. Base unit: Press and hold [HANDSET LOCATOR]. Handset: Press and hold [FLASH/CALL WAIT] until a beep sounds. · The VOICE ENHANCER indicator flashes. · When registration is complete, a beep sounds from the handset and the indicator lights go out. · Wait for 20 seconds after registration is complete while the handset establishes communication with the base unit. · If the handset beeps 3 times in step 2, an error occurred. · You can stop registration by pressing [OFF] on the handset, and pressing [HANDSET LOCATOR] on the base unit. · A fully charged battery will give you up to 5 hours of continuous talk time, or keep your handset in Standby mode to receive incoming calls for up to 11 days (if no phone calls are made). Battery power is consumed whenever the handset is off of the base unit, even when the handset is not in use. The longer you leave the handset off of the base unit, the time you can actually talk on the handset will be shortened. Actual battery performance depends on a combination of how often the handset is in TALK mode and how often it is in Standby mode. · If the battery is fully charged, you do not have to place the handset on the base unit until the RECHARGE indicator flashes. · If you want to keep the battery fully charged at all times, place the handset on the base unit when the handset is not used. · Clean the charge contacts of the handset and the base unit with a soft, dry cloth once a month. Clean more often if the unit is subject to grease, dust or high humidity. Move away from the microwave oven and closer to the base unit. · If you use the handset near another cordless phone's base unit, noise may be heard. Move away from the other cordless phone's base unit and closer to your base unit. 3 Tuck the telephone line cord inside the wall mounting adaptor, then push the adaptor in the direction of the arrows (# and $) while pressing the tabs. · The word "UP WALL" should face upward. 4-G Specifications 2 I Base unit Power Supply: Power Consumption: Frequency: Dimensions (H x W x D): Mass (Weight): I Handset Power Supply: Frequency: Dimensions (H x W x D): Mass (Weight): Security Codes: I Dialing Mode: I Operating Environment: 1 AC Adaptor (120 V AC, 60 Hz) Standby: Approx. 124 mm x 155 mm x 174 mm (4 7/8" x 6 3/32" x 6 27/32") Approx. [. . . ] Ganchos Toma telefónica de una sola línea (RJ11C) Cable de línea telefónica Toma de corriente (120 V CA, 60 Hz) Adaptador de CA Indicador CHARGE Sección 5 5-A Preparación 3 Cargue la batería durante unas 6 horas. · La unidad emite un pitido y el indicador CHARGE se ilumina. O Para obtener el máximo alcance y un funcionamiento sin ruidos, ponga la unidad base en un lugar ELEVADO y CÉNTRICO sin obstrucciones ni interferencias de aparatos eléctricos. · El adaptador de CA debe permanecer conectado en todo momento. Para seleccionar el modo de marcación por TONO (preajustado) o PULSACIÓN Asegúrese de que la unidad portátil y la unidad base no se están utilizando. La unidad portátil debe operarse cerca de la unidad base, y descolgada de la misma. Presione [VOICE ENHANCER], y luego presione [8]. [. . . ]