User manual PANASONIC KX-TG5202

[. . . ] 5. 8 GHz Expandable Cordless Phone System Operating Instructions Model No. KX-TG5200 KX-TG5202 Pulse-or-tone dialing capability Model shown is KX-TG5200. The unit is Caller ID compatible. To display the Caller's name and phone number, you must subscribe to Caller ID service. PLEASE READ BEFORE USE AND SAVE. Charge the battery for 6 hours before initial use. Panasonic World Wide Web address: http://www. panasonic. com for customers in the USA or Puerto Rico Thank you for purchasing your new Panasonic cordless telephone. Please read the IMPORTANT SAFETY INSTRUCTIONS on page 65 before use. [. . . ] *To prevent misdialing, you may add pauses between your voice mail access number and your mailbox password in step 5. 1-222-333-4444 PPPP 8888 Your voice mail access number Pauses Your mailbox password Pressing the soft key ( PAUSE ) once creates a 3. 5 second delay and counts as one digit. The delay time necessary between entering your access number and entering your mailbox password will depend on your telephone company. 40 Voice Mail Service To erase a stored voice mail access number Repeat steps 1 to 4 on page 40, then press and hold the soft key ( CLEAR ) until all of the digits are erased. Press the soft key ( SAVE ), then press [OFF]. Preparation Setting Voice Mail (VM) Tone Detection Handset Your telephone company sends special signals (Voice mail tones) to the unit. Press [C] or [s] to listen to the dial tone. If you hear a series of dial tones followed by a continuous dial tone, this indicates that a new message was recorded. Voice Mail detection is preset at the factory to ON. Minutes after you hang up or after the phone stops ringing, your unit will seize the phone line and check if a message has been recorded. If a new message was recorded at your telephone company, "Voice Mail" will be displayed on the handset, the Ringer/Message Alert indicator on the handset will flash slowly if Message Alert is turned on (p. 19), and the VM indicator will flash on the base unit. Turn off this programming when: -- you do not subscribe to a voice mail service, -- your telephone company does not send a series of tones, followed by a continuous tone to indicate you have new voice mail, or -- your phone is connected to a business or office telephone system (PBX). If you are not sure which setting is required, consult your local telephone company or contact the Panasonic Customer Call Center. Telephone System Advanced Operation 1 Press [MENU]. 2 Scroll to "Initial setting" by pressing [d] or [B], then press the soft key ( SELECT ). Initial setting Voice Mail VM tone detect VM tone detect 3 Press the soft key ( SELECT ) at "Voice Mail". 4 Scroll to "VM tone detect" by pressing [d] or [B], then press the soft key ( SELECT ). Useful Information 5 Select "Off" or "On" by pressing [d] or [B]. 6 Press the soft key ( SAVE ), then press [OFF]. :On For assistance, please call: 1-800-211-PANA(7262) 41 Voice Mail Service Listening to Voice Mail Messages Handset The unit will let you know that someone has left new voice mail for you: (a) the VM indicator will flash on the base unit, (b) "Voice Mail" will be displayed on the handset, (c) " V M " will flash on the handset, and (d) the Ringer/Message Alert indicator on the handset will flash slowly if Message Alert is turned on (p. 19) and the handset is not in use. To listen to your voice mail message(s) 1 Press the soft key ( or [s]. · "Dial VM access#" is displayed and the number is dialed (p. · If the handset beeps 3 times and "Store VM access#" is displayed, a voice mail access number is not stored. To store the number, see page 40. VM ), then press [C] Voice Mail VM 2 Follow the pre-recorded instructions. 3 When finished, press [OFF]. · After listening to your message(s), " V M " stops flashing but remains on the handset display. · If the handset and base unit still indicate you have new messages even after you have listened to them, turn the voice mail indicators off by pressing and holding [OFF] until the handset beeps. "Voice Mail" will disappear and " V M " stops flashing but remains on the handset, and the Ringer/Message Alert indicator on the handset and the VM indicator on the base unit will go out. · If your voice mail service uses a voice mail tone and the recorded message is over 3 minutes long, the handset and base unit may not indicate you have new messages. [. . . ] If the known working phone operates properly, have your unit repaired by one of the authorized Panasonic Factory Service Centers. If the known working phone does not operate properly, consult your telephone company. Preparation Telephone System Answering System Useful Information 69 For assistance, please call: 1-800-211-PANA(7262) Specifications N Handset Power Supply: Frequency: Ni-MH battery (3. 6 V, 830 mAh) 5. 76 GHz ­ 5. 84 GHz (8 21/32" x 2 3/32" x 1 15/32") Mass (Weight): Security Codes: Approx. 210 g (0. 46 lb. ) 1, 000, 000 Dimensions (H x W x D): Approx. 220 mm x 53 mm x 37 mm N Base Unit Power Supply: Power Consumption: Frequency: AC adaptor (120 V AC, 60 Hz) Standby: Maximum: Approx. [. . . ]