User manual PANASONIC KX-TG6411UA

[. . . ] (found on the bottom of the base unit) Date of purchase Name and address of dealer Note: L This equipment is designed for use on the UK and Republic of Ireland analogue telephone network. L In the event of problems, you should contact your equipment supplier in the first instance. Declaration of Conformity: L Panasonic Communications Co. , Ltd. declares that this equipment is in compliance with the essential requirements and other relevant provisions of Radio & Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC. [. . . ] 6 Enter the desired hour and minute you wish to start this feature by selecting 2 digits for each. L If you use 12-hour time entry, select "AM" or "PM" by pressing {*} repeatedly before entering the time. 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 3 Select "Ringer Setup", then press {>}. 4 Select "Night Mode", then press {>}. 5 Select "Ring Delay", then press {>}. 6 Select the desired setting, then press {>}. 7 Enter the desired hour and minute you wish to end this feature by selecting 2 digits for each. 7 Press {ih}. 20 Helpline Tel. 01289 8333 TCD200E(e-e). book Page 21 Wednesday, February 9, 2005 2:58 PM Handset Settings Selecting categories to bypass night mode 4 Select "Standby Display", then press {>}. 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 5 Select the desired setting, then press {>}. 6 Press {ih}. Note: L If "Base Number" is selected and the current base unit number is 2, "-2-" is displayed. L If "Handset Number" is selected and the current handset number is 2, "[2]" is displayed. 3 Select "Ringer Setup", then press {>}. 4 Select "Night Mode", then press {>}. 5 Select "Select Category", then press {>}. 6 Press the desired category numbers, then press {j/OK}. L The selected category number will flash. L To cancel a selected category number, press the number again. 5 Select "On" or "Off", then press {>}. 6 Press {ih}. 22 4 Select "Keytones", then press {>}. 5 Select "On" or "Off", then press {>}. 01289 8333 TCD200E(e-e). book Page 23 Wednesday, February 9, 2005 2:58 PM Handset Settings Note: L If keytones are turned off, error tones will not sound when you enter the wrong PIN or when memory is full. Resetting the handset to its default settings 1 Press {j/OK}. 2 Select "Handset Setup", then press {>}. 3 Select "Other Options", then press {>}. 4 Select "Reset Handset", then press {>}. 5 Enter "0000" (default handset PIN). L If you changed the PIN, enter it (page 22). 6 Select "Yes", then press {>}. 7 Press {ih}. Note: L The following items will be deleted or reset to their default settings: ­ Settings listed on page 18 ­ Redial list ­ Voice enhancer ­ Category names ­ Category ringtones L The following items will be retained: ­ Phonebook entries (category names and ringtones will be reset to their default settings. ) ­ Date and time Helpline Tel. 01289 8333 23 TCD200E(e-e). book Page 24 Wednesday, February 9, 2005 2:58 PM Base Unit Settings Guide to base unit settings For your reference, a chart of all items which can be customised for the base unit is printed below. L When customising the base unit, the current item or setting is indicated by >. Base unit settings menu Ringer Setup Sub-menu Sub-menu 2 Default setting Medium 23:00/06:00 Off 60 sec. 112, 999 -- 0000 Off -- Page page 25 page 25 page 25 page 25 page 26 page 26 page 26 page 26 page 27 page 33 page 27 Ringer Volume Night Mode Start/End On/Off Ring Delay Call Options Recall Pause Length Emergency No. Call Restrict Other Options Base Unit PIN Repeater Mode Reset Base Note: L Up to 3 menu items can be displayed at a time. [. . . ] 250 mW I Power source: 220­240 V, 50 Hz I Power consumption, Base unit: Standby: Approx. 9. 2 W I Operating conditions: 5 °C­40 °C, 20 %­80 % relative air humidity (dry) I Dimensions: Base unit: Approx. 111 mm × 121 mm × 123 mm Handset: Approx. 148 mm × 48 mm × 32 mm I Mass (weight): Base unit: Approx. [. . . ]