User manual PANASONIC KX-TG6422E

[. . . ] (found on the bottom of the base unit) Date of purchase Name and address of dealer Note: L In the event of problems, you should contact your equipment supplier in the first instance. Declaration of Conformity: L Panasonic Communications Co. , Ltd. declares that this equipment is in compliance with the essential requirements and other relevant provisions of Radio & Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC. Declarations of Conformity for the relevant Panasonic products described in this manual are available for download by visiting: http://www. doc. panasonic. de Contact: Panasonic Services Europe a Division of Panasonic Marketing Europe GmbH Panasonic Testing Centre Winsbergring 15, 22525 Hamburg, Germany Trademarks: L Eatoni and LetterWise are trademarks of Eatoni Ergonomics, Inc. 2 TCD230-240FX(e). book Page 3 Wednesday, June 8, 2005 7:15 PM Feature highlights Feature highlights Phonebooks This unit provides the handset phonebook (200 names and phone numbers; page 20) and the shared phonebook (20 names and phone numbers: KX-TCD240 only; page 22). [. . . ] L To change the base unit ringer volume and the base unit ringtone, see page 19. 32 TCD230-240FX(e). book Page 33 Wednesday, June 8, 2005 7:15 PM Base Unit Settings Ringer setup Night mode Night mode allows you to select a block of time during which the base unit will not ring for outside calls. This feature is useful for times when you do not want to be disturbed, for example, while sleeping. Night mode can be set independently for the handset (page 28) and the base unit. Set the date and time beforehand (page 14). Note: L To avoid disturbances, we recommend turning the call screening feature off (page 52) in addition to turning the night mode feature on (KX-TCD240 only). Setting the start and end time for night mode 9 Press {j/OK}. 10 Press {ih}. Turning night mode on/off 1 Press {j/OK}. 2 Select "Base Unit Setup", then press {>}. 3 Enter "0000" (default base unit PIN). L If you changed the PIN, enter it (page 35). 4 Select "Ringer Setup", then press {>}. 5 6 7 8 Select "Night Mode", then press {>}. Select "On/Off", then press {>}. Select "On" or "Off", then press {>}. 2 Select "Base Unit Setup", then press {>}. 3 Enter "0000" (default base unit PIN). L If you changed the PIN, enter it (page 35). Setting the ring delay for night mode This setting allows the base unit to ring during night mode if the caller waits long enough. L The base unit extension number "0" and the extension numbers of all registered handsets are displayed. 4 Select "Call Options", then press {>}. 5 Select "Call Bar", then press {>}. 6 Select "On" or "Off", then press {>}. 7 Press {ih}. 6 Select the extensions which will be restricted by pressing the desired number. L Flashing numbers indicate call restriction is turned on for the corresponding extension. L To turn call restriction off for an extension, press the dial key corresponding to its extension number. The number will stop flashing. Other options Changing the base unit PIN (Personal Identification Number) For security, the base unit PIN must be entered when changing certain settings. Important: L If you change the PIN, please make note of your new PIN. The unit will not reveal the PIN to you. If you forget your PIN, consult your nearest Panasonic service centre. 7 Press {j/OK}. 8 Select a memory location, then press {>}. L If the memory location already contains a restricted number, the number is displayed. 9 Enter the phone number or area code to be restricted (8 digits max. ), then press {j/OK}. [. . . ] Confirm that the correct SMS message centre numbers are stored (page 40). Confirm that SMS is turned on (page 40). L An error occurred while sending the message. L Your phone number is permanently withheld or you have not subscribed to the appropriate service. [. . . ]