User manual PANASONIC KX-TG6434

[. . . ] M i {ih} Basic operations Making/Answering calls (Handset) Making calls Answering calls To hang up To adjust the receiver/ speaker volume Making a call using the redial list Handset ringer volume Dial the phone number. i {C}/{s} {C}/{s} {ih} Press {^} or {V} repeatedly while talking. j (right soft key) i {V}/{^}: Select the desired phone number. i {C} 1 2 3 4 5 K (middle soft key) {V}/{^}: "Handset Setup" i M {V}/{^}: "Ringer Setup" i M {V}/{^}: "Ringer Volume" i M {V}/{^}: Select the desired volume. [. . . ] i M i {ih} Phonebook (Handset) Adding entries 1 n (left soft key) i K 2 {V}/{^}: "New Entry" i M 3 Enter the party's name (16 characters max. ). i M 4 Enter the party's phone number (24 digits max. ). i M 2 times i {ih} L To enter a name, see the character table in the operating instructions. Making calls 1 n (left soft key) 2 {V}/{^}: Select the desired entry. L You can scroll through the phonebook entry by pressing and holding {V} or {^}. 3 {C} ­3­ TG7301_7321E(e)_QG. fm Page 4 Thursday, February 14, 2008 11:28 AM Basic operations Answering system (Base unit): KX-TG7321/KX-TG7322/KX-TG7323/KX-TG7324 Answering on/off Listening to messages Press {s} to turn on/off the answering system. {6} Frequently asked questions Question Why is w flashing?Cause/solution L The handset is too far from the base unit. L The base unit's AC adaptor is not connected. L You are using the handset or base unit in an area with high electrical interference. Place the base unit and use the handset away from sources of interference. L The handset is not registered to the base unit. Place the base unit and use the handset away from sources of interference. L If you use a DSL/ADSL service, we recommend connecting a DSL/ADSL filter between the base unit and the telephone line jack. Contact your DSL/ADSL provider for details. L Clean the battery ends (S, T) and the charge contacts with a dry cloth, and charge again. What should I do when noise is heard, sound cuts in and out? What should I do when the operating time seems to be shorter even after I fully charged the batteries?What do I need to do to erase y (Missed call) from the display? L There are unviewed missed calls remaining. View them using the following method. 1 K (middle soft key) 2 {V}/{^}: "Caller List" i M 3 Press {V} to search from the most recent call, or press {^} to search from the oldest call. ­5­ TG7301_7321E(e)_QG. fm Page 6 Thursday, February 14, 2008 11:28 AM Registering a handset to the base unit The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit, register the handset. Handset 1 K (middle soft key) 2 {V}/{^}: "Handset Setup" i M 3 {V}/{^}: "Register H. set" i M M Base unit Proceed with the operation for your model. N KX-TG7301/KX-TG7302/KX-TG7303/ KX-TG7304 Press and hold {x} for about 5 seconds. [. . . ] N KX-TG7301/KX-TG7302/KX-TG7303/ KX-TG7304 Press and hold {x} for about 5 seconds. (No registration tone) N KX-TG7321/KX-TG7322/KX-TG7323/ KX-TG7324 Press and hold {x} for about 5 seconds, until the registration tone sounds. L The next step should be completed within 90 seconds. {x} {x} Handset Wait until "Enter Base PIN" is displayed. i Enter the base unit PIN (default: "0000"). [. . . ]