User manual PANASONIC KX-TG6481E

[. . . ] TG6481E(e). book Page 1 Thursday, May 7, 2009 1:36 PM Operating Instructions Digital Cordless Answering System Model No. KX-TG6481E KX-TG6482E Model shown is KX-TG6481. Thank you for purchasing a Panasonic product. You must subscribe to the appropriate service offered by your service provider/telephone company. Charge the batteries for about 7 hours before initial use. Please read these operating instructions before using the unit and save them for future reference. TG6481E(e). book Page 2 Thursday, May 7, 2009 1:36 PM Table of Contents Introduction Model composition . [. . . ] Important: L When the unit receives a call from a number that is stored in the call barred 8 Note: L You can skip to step 4 by pressing {R/E} in standby mode. 22 Helpline Tel. 01289 8333 TG6481E(e). book Page 23 Thursday, May 7, 2009 1:36 PM Programming list, the call is logged in the caller list (page 25) with 7 after the call is disconnected. Storing unwanted callers You can store up to 30 phone numbers in the call barred list by using the caller list or by entering the numbers directly. Important: L You must store the phone number with an area code in the call barred list. i M i {ic} Erasing a number: K i {V}/{^}: "Erase" i M i {V}/{^}: "Yes" i M i {ic} Note: L When editing, press the desired dial key to add, {C/T} to erase. Registering a unit Operating additional units Additional handsets Up to 6 handsets can be registered to the base unit. Important: L The additional handset model recommended for use with this unit is noted on page 4. If another handset model is used, certain operations (handset settings, base unit settings, etc. ) may not be available. 1 2 3 4 5 1 2 3 4 K (middle soft key) {V}/{^}: "Caller List" i M {V}/{^}: Select the entry to be barred. i K {V}/{^}: "Add Bar List" i M {ic} K (middle soft key) {V}/{^}: "Caller Barred" i Mi~ Enter the phone number (24 digits max. ). {ic} By entering phone numbers: Registering a handset to the base unit The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit (for example, w flashes even when the handset is near the base unit), reregister the handset. Viewing/editing/erasing bar call numbers 1 2 3 4 K (middle soft key) {V}/{^}: "Caller Barred" i M {V}/{^}: Select the desired entry. Editing a number: K i {V}/{^}: "Edit" i M i Press {<} or {>} to 1 2 3 Handset: K (middle soft key) {V}/{^}: "Handset Setup" i M {V}/{^}: "Register H. set" i M Helpline Tel. 01289 8333 23 TG6481E(e). book Page 24 Thursday, May 7, 2009 1:36 PM Programming 4 Base unit: Press and hold {x} for about 5 seconds, until the registration tone sounds. L If all registered handsets start ringing, press the same button to stop. L The next step must be completed within 90 seconds. Handset: Wait until "Enter Base PIN" is displayed. i Enter the base unit PIN (default: "0000"). i M L If you forget your PIN, see page 41. L When the handset has been registered successfully, w stops flashing. L To cancel a selected handset number, press the number again. The number stops flashing. 6 5 {V}/{^}: "Yes" i M L A confirmation tone sounds as each handset number disappears. L The handset does not beep when cancelling its own registration. {ic} 7 Increasing the range of the base unit You can increase the signal range of the base unit by using a DECT repeater. Please use only the Panasonic DECT repeater noted on page 4. [. . . ] Remove the batteries from the handset and leave to dry for at least 3 days. After the handset/base unit are completely dry, reconnect the AC adaptor and telephone line cord. Insert the batteries and charge fully before use. If the unit does not work properly, contact your nearest Panasonic service centre. Caution: L To avoid permanent damage, do not use a microwave oven to speed up the drying process. Helpline Tel. [. . . ]