User manual PANASONIC KX-TG6481UA

[. . . ] (found on the bottom of the base unit) Date of purchase Name and address of dealer Note: L In the event of problems, you should contact your equipment supplier in the first instance. Declaration of Conformity: L Panasonic Communications Co. , Ltd. declares that this equipment is in compliance with the essential requirements and other relevant provisions of Radio & Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC. Declarations of Conformity for the relevant Panasonic products described in this manual are available for download by visiting: http://www. doc. panasonic. de Contact: Panasonic Services Europe GmbH Panasonic Testing Centre Winsbergring 15, 22525 Hamburg, F. R. [. . . ] Select "On" or "Off", then press {>}. 2 Select "Base Unit Setup", then press {>}. 3 Enter "0000" (default base unit PIN). 30 Setting the ring delay for night mode This setting allows the base unit to ring during night mode if the caller waits long enough. After the selected amount of time passes, the base unit will ring, useful when someone urgently needs to speak with you. TCD210220FX(e-e). book Page 31 Tuesday, January 18, 2005 9:04 AM Base Unit Settings If you select "No Ringing", the base unit will not ring during night mode. Changing the recall time Change the recall time, if necessary, depending on the requirements of your service provider or PBX. 1 Press {j/OK}. 2 Select "Base Unit Setup", then press {>}. 3 Enter "0000" (default base unit PIN). L If you changed the PIN, enter it (page 32). 1 Press {j/OK}. 2 Select "Base Unit Setup", then press {>}. 4 Select "Ringer Setup", then press {>}. 3 Enter "0000" (default base unit PIN). L If you changed the PIN, enter it (page 32). 5 Select "Night Mode", then press {>}. 6 Select "Ring Delay", then press {>}. 7 Select the desired setting, then press {>}. 4 Select "Call Options", then press {>}. 8 Press {ih}. 5 Select "Recall", then press {>}. 6 Select the desired setting, then press {>}. 7 Press {ih}. Call options Setting dialling mode (tone/pulse) "Tone": Select when you have a touch tone service. "Pulse": Select when you have rotary or pulse service. Setting pause length Change the pause length, if necessary, depending on the requirements of your service provider or PBX. 1 Press {j/OK}. 2 Select "Base Unit Setup", then press {>}. 1 Press {j/OK}. 2 Select "Base Unit Setup", then press {>}. 3 Enter "0000" (default base unit PIN). L If you changed the PIN, enter it (page 32). 3 Enter "0000" (default base unit PIN). L If you changed the PIN, enter it (page 32). 4 Select "Call Options", then press {>}. 5 Select "Pause Length", then press {>}. 4 Select "Call Options", then press {>}. 6 Select the desired setting, then press {>}. 5 Select "Dial Mode", then press {>}. 2 Select "Base Unit Setup", then press {>}. 3 Enter "0000" (default base unit PIN). L If you changed the PIN, enter it (page 32). 4 Select "Other Options", then press {>}. 5 Select "Reset Base", then press {>}. 6 Select "Yes", then press {>}. 7 Press {ih}. Note: L The following items will be deleted or reset to their default settings: ­ Settings listed on page 29, 39, 48 ­ All SMS messages ­ Caller list L The following items will be retained: ­ Date and time ­ Shared phonebook entries (KXTCD220 only) ­ Repeater mode ­ Recordings, including your greeting message, caller messages, voice memos, audible call announcements, and recorded conversations (KXTCD220 only) 33 TCD210220FX(e-e). book Page 34 Tuesday, January 18, 2005 9:04 AM Caller ID Service Using Caller ID service Important: L This unit is Caller ID compatible. To use Caller ID features (such as displaying caller phone numbers), you must subscribe to Caller ID service. Consult your service provider for details. Caller ID features When an outside call is received, the caller's phone number can be displayed. L Phone numbers of the last 50 different callers will be logged in the caller list. L While listening to a message recorded by the answering system, you can call back the caller without having to dial the phone number (KX-TCD220 only; page 44). L When caller information is received and it matches a phone number stored in the unit's phonebook: ­ The stored name will be displayed and logged in the caller list. ­ The handset will use the ringtone assigned to the caller's category. ­ The handset will announce the audible call recording you made (KX-TCD220 only). [. . . ] Confirm that the correct SMS message centre numbers are stored (page 36). Confirm that SMS is turned on (page 36). L An error occurred while sending the message. L Your phone number is permanently withheld or you have not subscribed to the appropriate service. [. . . ]