User manual PANASONIC KX-TG7301E

[. . . ] *2 KX-TG7302/KX-TG7303/ KX-TG7304/KX-TG7322/ KX-TG7323/KX-TG7324 Note: L USE ONLY Ni-MH batteries AAA (R03) size. L Do NOT use Alkaline/Manganese/Ni-Cd batteries. Operating tips Using the navigator key The handset navigator key can be used to navigate through menus and to select items shown on the display by pressing {^}, {V}, {<}, or {>}. To adjust the receiver or speaker volume, press {^} to increase the volume, or press {V} to decrease the volume repeatedly while talking. Volume up {^} {<} {>} {V} Volume down Soft keys The handset features 3 soft keys. By pressing a soft key, you can select the feature shown directly above it on the display. ­2­ TG7301_7321E(e)_QG. fm Page 3 Thursday, February 14, 2008 11:28 AM Date and time (Handset) 1 2 3 4 5 6 7 K (middle soft key) {V}/{^}: "Handset Setup" i M {V}/{^}: "Time Settings" i M {V}/{^}: "Set Date & Time" i M Enter the current date, month, and year. [. . . ] L The handset is not registered to the base unit. L Make sure the batteries are installed correctly. L Clean the charge contacts and charge again. L When you are using fully-charged Ni-MH batteries (supplied batteries); In continuous use: 17 hours max. L It is normal for batteries not to reach full capacity at the initial charge. Maximum battery performance is reached after a few complete cycles of charge/discharge (use). L Actual battery performance depends on a combination of how often the handset is in use and how often it is not in use (standby). L Even after the handset is fully charged, the handset can be left on the base unit or charger without any ill effect on the batteries. L If the batteries are fully charged until 1 is displayed, but 3 is displayed after a few calls, replace the batteries with new ones. L The PIN is a 4-digit number that must be entered in order to change certain base unit settings. The default PIN is "0000". What should I do when the handset does not turn on?How long is the battery operating time? Can I keep the handset on the base unit or charger when I am not using it?What is a PIN? ­4­ TG7301_7321E(e)_QG. fm Page 5 Thursday, February 14, 2008 11:28 AM Frequently asked questions Question What should I do to display caller information?Cause/solution L You must subscribe to a Caller ID service. Contact your service provider/telephone company for details. L The message "You must first subscribe to Caller ID. " will be displayed until you receive caller information after subscribing to a Caller ID service. L You are using the handset or base unit in an area with high electrical interference. Place the base unit and use the handset away from sources of interference. [. . . ] i M L When the handset has been registered successfully, w stops flashing. M ­6­ TG7301_7321E(e)_QG. fm Page 7 Thursday, February 14, 2008 11:28 AM Optional service (Caller ID) If you subscribe to a Caller ID service, you can: 012345 ­ display caller information Sales and support information Customer Care Centre L For customers within the UK: 0844 844 3898 L For customers within the Republic of Ireland: 01289 8333 L Visit our website for product information: www. panasonic. co. uk L E-mail: customer. care@panasonic. co. uk Direct Sales at Panasonic UK L Order accessory and consumable items for your product with ease and confidence by phoning our Customer Care Centre Monday - Thursday 9:00am 5:30pm, Friday 9:30am - 5:30pm (Excluding public holidays). L Or go on line through our Internet Accessory ordering application at www. panasonic. co. uk L Most major credit and debit cards accepted. L All enquiries transactions and distribution facilities are provided directly by Panasonic UK Ltd. L Also available through our Internet is direct shopping for a wide range of finished products, take a browse on our website for further details. Customer Care Helpline Tel. [. . . ]