User manual PANASONIC KX-TG7303MB

[. . . ] Plug Guide Do not try to connect over the guide. Important: L If you use a telephone line cord which is not supplied, the unit may not work properly. Charger (KX-TG7302/KX-TG7303) Press plug firmly. Hooks (220-240 V AC, 50 Hz) Use only the supplied Panasonic AC adaptor PQLV209CE. PNQW1236ZA DC0608DN0 MB-2/3 TG7301_7321MB(e)_QG. fm Page 2 Thursday, May 22, 2008 3:56 PM Battery installation/Battery charge Charge for about 7 hours. Rechargeable Ni-MH ONLY Base unit *1 Charger *2 "Charging" will be displayed. *1 Model shown is KX-TG7301. *2 KX-TG7302/KX-TG7303 Note: L USE ONLY Ni-MH batteries AAA (R03) size. L Do NOT use Alkaline/Manganese/Ni-Cd batteries. Operating tips Using the navigator key The handset navigator key can be used to navigate through menus and to select items shown on the display by pressing {^}, {V}, {<}, or {>}. To adjust the receiver or speaker volume, press {^} to increase the volume, or press {V} to decrease the volume repeatedly while talking. Volume up {^} {<} {>} {V} Volume down Soft keys The handset features 3 soft keys. [. . . ] L You can scroll through the phonebook entry by pressing and holding {V} or {^}. {C} Answering system (Base unit): KX-TG7321 Answering on/off Listening to messages Press {s} to turn on/off the answering system. {6} Frequently asked questions Question Why is w flashing?Cause/solution L The handset is too far from the base unit. L The base unit's AC adaptor is not connected. L You are using the handset or base unit in an area with high electrical interference. Place the base unit and use the handset away from sources of interference. L The handset is not registered to the base unit. L The dialling mode may be set incorrectly. Change the setting (page 3). Why can I not make calls? ­4­ TG7301_7321MB(e)_QG. fm Page 5 Thursday, May 22, 2008 3:56 PM Frequently asked questions Question What should I do when the handset does not turn on?Cause/solution L Make sure the batteries are installed correctly. L Clean the charge contacts and charge again. L When you are using fully-charged Ni-MH batteries (supplied batteries); In continuous use: 17 hours max. L It is normal for batteries not to reach full capacity at the initial charge. Maximum battery performance is reached after a few complete cycles of charge/discharge (use). L Actual battery performance depends on a combination of how often the handset is in use and how often it is not in use (standby). L Even after the handset is fully charged, the handset can be left on the base unit or charger without any ill effect on the batteries. L If the batteries are fully charged until 1 is displayed, but 3 is displayed after a few calls, replace the batteries with new ones. L The PIN is a 4-digit number that must be entered in order to change certain base unit settings. L You must subscribe to a Caller ID service. [. . . ] Handset 1 2 3 K (middle soft key) {V}/{^}: "Handset Setup" i M {V}/{^}: "Register H. set" i M M Base unit Proceed with the operation for your model. N KX-TG7301/KX-TG7302/KX-TG7303 Press and hold {x} for about 5 seconds. (No registration tone) N KX-TG7321 Press and hold {x} for about 5 seconds, until the registration tone sounds. L The next step should be completed within 90 seconds. {x} {x} Handset Wait until "Enter Base PIN" is displayed. [. . . ]