User manual PANASONIC KX-TG7331FX

[. . . ] Plug Hook (220-240 V AC, 50 Hz) Press plug firmly. Use only the supplied Panasonic AC adaptor PQLV207CE. Important: L If you use a telephone line cord which is not supplied, the unit may not work properly. PNQW1226ZA DC0708DN0 FX-3/4 TG7331_7341FX(e)_QG. fm Page 2 Friday, July 11, 2008 9:47 AM Battery installation/Battery charge Charge for about 7 hours. Rechargeable Ni-MH ONLY "Charging" is displayed. * Model shown is KX-TG7331. Note: L USE ONLY Ni-MH batteries AAA (R03) size. L Do NOT use Alkaline/Manganese/Ni-Cd batteries. Operating tips Using the navigator key The handset navigator key can be used to navigate through menus and to select items shown on the display by pressing {^}, {V}, {<}, or {>}. [. . . ] Press {^} or {V} repeatedly to select the desired volume. L To turn the ringer off, press and hold {V} until the unit beeps. ­4­ TG7331_7341FX(e)_QG. fm Page 5 Friday, July 11, 2008 9:47 AM Basic operations Phonebook (Handset) Adding entries 1 n (left soft key) i K 2 {V}/{^}: "New Entry" i M 3 Enter the party's name (16 characters max. ). i M L You can change the character entry mode by pressing /. 4 Enter the party's phone number (24 digits max. ). i M 2 times i {ih} L To enter a name, see the character table in the operating instructions. Making calls 1 n (left soft key) 2 {V}/{^}: Select the desired entry. L You can scroll through the phonebook entry by pressing and holding {V} or {^}. 3 {C} Answering system (Base unit): KX-TG7341 Answering on/off Listening to messages Press {s} to turn on/off the answering system. {6} Frequently asked questions Question Why is w flashing?Cause/solution L The handset is too far from the base unit. L The base unit's AC adaptor is not connected. L You are using the handset or base unit in an area with high electrical interference. Re-position the base unit and use the handset away from sources of interference. L The handset is not registered to the base unit. L The dialling mode may be set incorrectly. L Make sure the batteries are installed correctly. L Clean the charge contacts and charge again. Why can I not make calls?What should I do when the handset does not turn on? ­5­ TG7331_7341FX(e)_QG. fm Page 6 Friday, July 11, 2008 9:47 AM Frequently asked questions Question How long is the battery operating time?Cause/solution L When you are using fully-charged Ni-MH batteries (supplied batteries); In continuous use: 17 hours max. L It is normal for batteries not to reach full capacity at the initial charge. Maximum battery performance is reached after a few complete cycles of charge/discharge (use). L Actual battery performance depends on a combination of how often the handset is in use and how often it is not in use (standby). L Even after the handset is fully charged, the handset can be left on the base unit or charger without any ill effect on the batteries. L If the batteries are fully charged until 1 is displayed, but 3 is displayed after a few calls, replace the batteries with new ones. [. . . ] View them and erase y in the following way. 1 K (middle soft key) 2 {V}/{^}: "Caller List" i M 3 Press {V} to search from the most recent call, or press {^} to search from the oldest call. ­7­ TG7331_7341FX(e)_QG. fm Page 8 Friday, July 11, 2008 9:47 AM Registering a handset to the base unit The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit, re-register the handset. Handset 1 K (middle soft key) 2 {V}/{^}: "Handset Setup" i M 3 {V}/{^}: "Register H. set" i M M Base unit Press and hold {x} for about 5 seconds, until the registration tone sounds. L The next step must completed within 90 seconds. N KX-TG7331 {x} N KX-TG7341 {x} Handset Wait until "Enter Base PIN" is displayed. [. . . ]