User manual PANASONIC KX-TG8012FX

[. . . ] TG8011-8021FX(e-e). book Page 1 Wednesday, August 20, 2008 9:50 AM Operating Instructions Digital Cordless Phone Model No. KX-TG8011FX KX-TG8012FX KX-TG8021FX Digital Cordless Answering System Model No. Model shown is KX-TG8011. This unit is compatible with Caller ID and SMS. You must subscribe to the appropriate service offered by your service provider/telephone company. Charge the batteries for about 7 hours before initial use. To use this unit in your country, first change the unit's region setting to match your country (page 29). [. . . ] L To cancel a selected category number, press the number again. {ih} Changing the unit's region setting/Resetting the base unit 1 K (middle soft key) i < i M 2 3 {V}/{^}: "Country" i M {V}/{^}: Select the desired country. iM 6 Changing the base unit PIN (Personal Identification Number) Important: L If you change the PIN, please make note of your new PIN. The unit will not reveal the PIN to you. If you forget your PIN, contact your nearest Panasonic service centre. countries except Czech and Slovakia Czech Slovakia 4 {V}/{^}: "Yes" i M i {ih} 1 2 3 4 K (middle soft key) i < i M {V}/{^}: "Base Unit PIN" i M Enter the current 4-digit base unit PIN (default: "0000"). i M i {ih} Note: L The following items will be deleted or reset to their default settings: ­ Base unit settings (page 25) ­ SMS settings (page 38) ­ Answering system settings (KX-TG8021, page 43) ­ Time Adjustment ­ All SMS messages ­ Caller list ­ Voice mail messages L The following items will be retained: ­ Date and time ­ Repeater mode ­ Recordings, including your greeting message and caller messages (KX-TG8021) ­ Call screening (KX-TG8021) L If you select the desired country in step 3, the following default settings will be changed for the selected country's default settings: ­ Display language (page 25) 29 TG8011-8021FX(e-e). book Page 30 Wednesday, August 20, 2008 9:50 AM Programming L According to your country selection in step 3, the answering system announcement language changes as follows (KX-TG8021): Note: L Calls are disconnected when the handset moves from one radio cell to another. - "Other" - English Czech Slovak Registering a handset to a base unit The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit (for example, w flashes even when the handset is near the base unit), reregister the handset. L After changing the unit's region setting/resetting the base unit, w flashes on the handset momentarily. This is normal and the handset can be used once w stops flashing. 1 Registering a unit Operating additional units Additional handsets Up to 6 handsets can be registered to a single base unit. Important: L The additional handset model recommended for use with this unit is noted on page 5. If another handset model is used, certain operations (handset settings, base unit settings, etc. ) may not be available. Additional base units Handsets can be registered to up to 4 base units, allowing you to add additional base units and extend the area in which your handset(s) can be used. If a handset moves out of range of its base unit when "Auto" is selected on base unit (page 31), it looks for another base unit to make or receive calls. A base unit and the handsets it communicates with is called a "radio cell". Handset: K (middle soft key) i N i M {V}/{^}: "Registration" i M 2 times {V}/{^}: Select a base unit number. iM L This number is used by the handset as a reference only. Base unit: Proceed with the operation for your model. KX-TG8011/KX-TG8012 Press and hold {x} for about 5 seconds. (No registration tone) KX-TG8021 Press and hold {x} for about 5 seconds, until the registration tone sounds. L If all registered handsets start ringing, press the same button to stop. L The next step must be completed within 90 seconds. 2 3 4 5 Handset: Wait until "Enter Base PIN" is displayed. i Enter the base unit PIN (default: "0000"). i M 30 TG8011-8021FX(e-e). book Page 31 Wednesday, August 20, 2008 9:50 AM Programming L If you forget your PIN, contact your nearest Panasonic service centre. L When the handset has been registered successfully, w stops flashing. [. . . ] Move closer. My own greeting message cannot be properly heard. I cannot operate the answering system. 56 TG8011-8021FX(e-e). book Page 57 Wednesday, August 20, 2008 9:50 AM Useful Information Problem I cannot operate the answering system remotely. Cause/solution L You are entering the wrong remote access code. If you have forgotten your remote access code, enter the remote access code setting to check your current code (page 42). [. . . ]