User manual PANASONIC KX-TG8280FX

[. . . ] TG8280FX(e). book Page 1 Tuesday, September 11, 2007 1:52 PM Operating Instructions Digital Cordless Answering System Model No. KX-TG8280FX This unit is Caller ID compatible. To display the caller's phone number, you must subscribe to Caller ID service. Charge the batteries for about 7 hours before initial use. To use this unit in your country, first change the unit's region setting to match your country (page 31). Change the unit's display language as needed (page 14). [. . . ] Selecting categories to bypass night mode 1 2 3 4 5 " (middle soft key) i N i # {^}/{V}: "Ringer Setup" i # {^}/{V}: "Night Mode" i # {^}/{V}: "Select Category" i # Press the desired category numbers. i # L The selected category number will flash. 28 TG8280FX(e). book Page 29 Tuesday, September 11, 2007 1:52 PM L Base Unit Settings Base unit settings To customise the base unit using the handset: 1 2 3 4 5 " (middle soft key) Select L by pressing {^}, {V}, {<}, or {>}. i # Press {^} or {V} to select the desired item in the base unit settings menu. i # Press {^} or {V} to select the desired item in the sub-menu. i # L In some cases, you may need to select from a second sub-menu. i # Press {^} or {V} to select the desired setting. i # L This step may vary depending on the feature being programmed. L To exit the operation, press {ih}. Note: L The current item or setting is highlighted on the display. Menu Ringer Setup Sub-menu (default setting) Ringer Volume For base unit Sub-menu 2 (default setting) Line1 (Medium)*1 Line2 (Medium)*1 Ext. Ringtone For outside calls Line1 ("Ringtone Line2 ("Ringtone Call Options Dial Mode ("Tone"): page 15 Recall/Flash Recall/Flash time*2 -- Line1 ("600 msec. "*3) Line2 ("600 msec. "*3) Call Restrict page 31 Line1 Line2 1") 2") 29 TG8280FX(e). book Page 30 Tuesday, September 11, 2007 1:52 PM L Base Unit Settings Menu Other Options Sub-menu (default setting) Line Select ("Auto"): page 15 Base Unit PIN Change base unit PIN ("0000"). *4 ­ Enter the current 4-digit base unit PIN. *5 ­ Enter the new 4-digit base unit PIN. i # i {ih} Repeater Mode ("Off"): page 44 Country Change the unit's region setting ("Other"): page 31 Sub-menu 2 (default setting) -- -- -- -- *1 When the ringer volume is turned off, and/or is displayed and the base unit does not ring for outside calls. However, when the ringer volume for both lines is turned off, the base unit will still ring at the minimum level for intercom calls. *2 Change the recall/flash time, if necessary, depending on the requirements of your service provider/telephone company or PBX. *3 When using the unit in Czech/Slovakia/Turkey, select the recall/flash time as follows: Czech/Slovakia = "100 msec. " Turkey = "200 msec. " If you change the unit's region setting/reset the base unit, the recall/flash time will be reset to the default setting. In this case, select the recall/flash time again. *4 If you change the PIN, please make note of your new PIN. The unit will not reveal the PIN to you. *5 If you forget your PIN, consult your nearest Panasonic service centre. 30 TG8280FX(e). book Page 31 Tuesday, September 11, 2007 1:52 PM L Base Unit Settings 9 Special instructions for call options Setting call restriction The dialling of certain numbers can be restricted. You can assign up to 6 phone numbers for each line, and select which unit (the base unit and/or selected handsets) to be restricted. Storing area codes will prevent the restricted units from dialling any phone number in that area code. Enter the phone number or area code to be restricted (8 digits max. ). i # i {ih} L To erase a restricted number, press {C/T}. Special instructions for other options Changing the unit's region setting/Resetting the base unit 1 " (middle soft key) i L i # 1 2 3 4 " (middle soft key) i L i # {^}/{V}: "Call Options" i # {^}/{V}: "Call Restrict" i # Enter the base unit PIN (default: "0000"). L If you forget your PIN, consult your nearest Panasonic service centre. [. . . ] L If you subscribe to the voice mail service, messages are recorded by your service provider/telephone company not your telephone. Change the unit's "Number of Rings" setting or consult your service provider/telephone company (page 42). L The base unit or another handset is being used. L The handset is too far from the base unit. [. . . ]