User manual PANASONIC KX-TG8302UA

[. . . ] (found on the bottom of the base unit) Date of purchase Name and address of dealer Note: L This equipment is designed for use on the UK and Republic of Ireland analogue telephone network. L In the event of problems, you should contact your equipment supplier in the first instance. Declaration of Conformity: L Panasonic Communications Co. declares that this equipment is in compliance with the essential requirements and other relevant provisions of Radio & Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC. [. . . ] Select "On" or "Off", then press {>}. 2 Select "Base Unit Setup", then press {>}. Setting the ring delay for night mode This setting allows the base unit to ring during night mode if the caller waits long enough. After the selected amount of time passes, the base unit will ring, useful when someone urgently needs to speak with you. If you select "No Ringing", the base unit will not ring during night mode. 3 Enter "0000" (default base unit PIN). L If you changed the PIN, enter it (page 34). 1 Press {j/OK}. 2 Select "Base Unit Setup", then press {>}. 4 5 6 7 Select "Ringer Setup", then press {>}. Select "Night Mode", then press {>}. Select "Start/End", then press {>}. Enter the desired hour and minute you wish to start this feature by selecting 2 digits for each. L If you use 12-hour time entry, select "AM" or "PM" by pressing {*} repeatedly before entering the time. 3 Enter "0000" (default base unit PIN). L If you changed the PIN, enter it (page 34). 4 5 6 7 8 Select "Ringer Setup", then press {>}. Select "Night Mode", then press {>}. Select "Ring Delay", then press {>}. 2 Select "Base Unit Setup", then press {>}. 7 Press {j/OK}. 33 Helpline Tel. 01289 8333 Base Unit Settings 8 Select a memory location, then press {>}. L If the memory location already contains a restricted number, the number is displayed. Resetting the base unit to its default settings 1 Press {j/OK}. 2 Select "Base Unit Setup", then press {>}. 9 Enter the phone number or area code to be restricted (8 digits max. ), then press {j/OK}. L To erase a restricted number, press {C/T}. 3 Enter "0000" (default base unit PIN). L If you changed the PIN, enter it (page 34). 10 Press {ih}. Other options Changing the base unit PIN (Personal Identification Number) For security, the base unit PIN must be entered when changing certain settings. Important: L If you change the PIN, please make note of your new PIN. The unit will not reveal the PIN to you. If you forget your PIN, consult your nearest Panasonic service centre. 4 5 6 7 Select "Other Options", then press {>}. Select "Reset Base", then press {>}. Select "Yes", then press {>}. 2 Select "Base Unit Setup", then press {>}. 3 Enter "0000" (default base unit PIN). L If you changed the PIN, enter it. Note: L The following items will be deleted or reset to their default settings: ­ Settings listed on page 31, 42, 51 ­ All SMS messages ­ Private mailbox settings for SMS ­ Caller list L The following items will be retained: ­ Date and time ­ Shared phonebook entries ­ Recordings, including your greeting message, caller messages, voice memos, audible call announcements, and recorded conversations 4 Select "Other Options", then press {>}. 5 Select "Base Unit PIN", then press {>}. [. . . ] Cause & solution L The recording time is set to "Greeting Only". Select "1 Minute" or "3 Minutes" (page 52). Erase unnecessary messages (page 48). 64 Helpline Tel. 01289 8333 Useful Information Problem I cannot operate the answering system with the handset. [. . . ]