User manual PANASONIC KX-TG8421FX

[. . . ] Activate the handset display again by: ­ pushing the joystick left {<} or right {>} when on a call. ­ pressing {ih} at all other times. {<}, {>} {ih} ­2­ TG8411_8421FX(e)_QG. fm Page 3 Wednesday, January 21, 2009 3:43 PM Operating tips Joystick By pushing the joystick ({^}, {V}, {<}, or {>}) repeatedly, you can: - scroll through (up, down, left, or right) various lists or items - adjust the receiver or speaker volume (up or down) while talking Volume up Volume down Soft keys The handset features 2 soft keys and a joystick. By pressing a soft key, or by pressing the centre of the joystick, you can select the feature shown directly above it on the display. Temporary switching the display mode You can switch the display mode (single item/multi items) temporarily for the features below by pressing A. - menu list, phonebook list, caller list, redial list, and recorded message list - handset top menu icons shown below Icon j K I X Feature Caller List Time Settings*1 Answer System*2 SMS (Short Message Service) Icon N ! [. . . ] i M 2 times i {ih} Making calls 1 n (left soft key) 2 {V}/{^}: Select the desired entry. L You can scroll through the phonebook entry by pushing and holding the joystick down or up. 3 {C} Answering system (Base unit): KX-TG8421 Answering on/off Listening to messages Press {s} to turn on/off the answering system. {6} ­5­ TG8411_8421FX(e)_QG. fm Page 6 Wednesday, January 21, 2009 3:43 PM Frequently asked questions Question Why is w flashing?Cause/solution L The handset is too far from the base unit. L The base unit's AC adaptor is not properly connected. L You are using the handset or base unit in an area with high electrical interference. Re-position the base unit and use the handset away from sources of interference. L The handset is not registered to the base unit. L The dialling mode may be set incorrectly. Activate the handset display again by: ­ pushing the joystick left {<} or right {>} when on a call. L "LCD in charging" is set to "Off" while on charge. L Make sure the batteries are installed correctly. L Clean the charge contacts and charge again. L When you are using fully-charged Ni-MH batteries (supplied batteries); In continuous use: 15 hours max. Not in use (standby): 250 hours (10 days) max. L It is normal for batteries not to reach full capacity at the initial charge. Maximum battery performance is reached after a few complete cycles of charge/discharge (use). L Actual battery performance depends on a combination of how often the handset is in use and how often it is not in use (standby). L Even after the handset is fully charged, the handset can be left on the base unit or charger without any ill effect on the batteries. L If the batteries are fully charged until & is displayed, but ) is displayed after a few calls, replace the batteries with new ones. Why can I not make calls?Why is the handset display blank or dark? What should I do when the handset does not turn on? [. . . ] View them and erase y in the following way. 1 1 (centre of joystick) i j i M 2 Push the joystick down to search from the most recent call, or push the joystick up to search from the oldest call. ­7­ TG8411_8421FX(e)_QG. fm Page 8 Wednesday, January 21, 2009 3:43 PM Registering a handset to a base unit The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit, re-register the handset. Handset 1 1 (centre of joystick) i N i M 2 {V}/{^}: "Register" i M 2 times 3 {V}/{^}: Select a base unit number. i M M Base unit Proceed with the operation for your model. [. . . ]