User manual PANASONIC KX-TGL430

[. . . ] For assistance, visit our Web site: http://shop. A B C D E F *1 *2 *3 *4 A Accessory item/Part number AC adaptor/PNLV226-0X Telephone line cord*1 Wall mounting adaptor/PNKL1061Z2 Rechargeable batteries*2 Handset cover*3/PNYNTGLA40BR Charger*4 KX-TGL430 1 1 1 2 1 – KX-TGL432 1 1 1 4 2 1 KX-TGL433 KX-TG3683 1 1 1 6 3 2 PQJA10075Y (Black cord), PQJA10075Z (Transparent cord) See page 4 for replacement battery information. The handset cover comes attached to the handset. Pdf 3 2015/11/17 16:08:02 Introduction Additional/replacement accessories Please contact your nearest Panasonic dealer for sales information (page 59). [. . . ] R The monitored handset never rings while it is being monitored. If the base unit is placed near the monitored handset, we recommend turning off the base unit ringer volume (page 15). 3 4 5 6 7 1 2 Changing the start and end time MMENUN#237 Continue from step 3, “Turning silent mode on/off”, page 29. Selecting groups to bypass silent mode Setting the baby monitor Perform the setting operation with the handset to be monitored (for example, the handset placed in a baby’s room). 1 2 MMENUN#241 MbN: Select the desired groups. A MSELECTN R “ ” is displayed next to the selected group numbers. R To cancel the selected group: MbN: Select the group. MSAVEN a MOFFN To monitor with a unit The internal baby monitor feature is available between handsets. 3 Baby monitor This feature allows you to listen in on a room where another handset is located, allowing you to easily monitor from different areas of the house or even while away from home. The monitored handset (placed in a baby’s room, for example) will automatically call the monitoring handset or the phone number stored when it detects sound. Important: R Before using this feature, we recommend that you test this feature and adjust the baby monitor sensitivity as needed, MbN: Select the desired unit’s number to monitor with. Pdf 31 2015/11/17 16:08:03 Programming If you want to respond from your monitoring phone, press #1 using tone dialing. You can turn off the baby monitor feature by pressing #0. Note: R The unit disconnects the call automatically after 2 minutes. Registering a handset to the base unit The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit, re-register the handset. 1 Handset: MMENUN#130 Base unit: Press and hold MLOCATORN for about 5 seconds. R If all registered handsets start ringing, press MLOCATORN again to stop, then repeat this step. Handset: Press MOKN, then wait until a long beep sounds. Other programming Changing the handset name The default handset name is “Handset 1” to “Handset 6”. You can customize the name of each handset (“Bob”, “Kitchen”, etc. This is useful when you make intercom calls between handsets. [. . . ] Pdf 52 2015/11/17 16:08:05 Useful Information Compliance with TIA-1083 standard: Telephone handsets identified with this logo have reduced noise and interference when used with T-Coil equipped hearing aids and cochlear implants. Compatible with Hearing Aid T-Coil T TIA-1083 For assistance, please visit http://shop. For all your Panasonic gear Go to hƩp://shop. Com/support Get everything you need to get the most out of your Panasonic products Accessories & Parts for your Camera, Phone, A/V products, TV, Computers & Networking, Personal Care, Home Appliances, Headphones, BaƩeries, Backup Chargers & more… Customer Services Directory For Product InformaƟon, OperaƟng Assistance, Parts, Owner’s Manuals, Dealer and Service info go to hƩp://shop. [. . . ]