User manual PANASONIC KX-TS105

[. . . ] Integrated Telephone System Preparation Operating Instructions Model No. KX-TS105B KX-TS105W Pulse-or-tone dialing capability Basic Operation Advanced Operation KX-TS105W Useful Information PLEASE READ BEFORE USE AND SAVE. Panasonic World Wide Web address: http://www. panasonic. com for customers in the USA or Puerto Rico Before Initial Use Please read IMPORTANT SAFETY INSTRUCTIONS on page 27 before use. Read and understand all instructions. Thank you for purchasing your new Panasonic integrated telephone. For your future reference Serial No. (found on the bottom of the unit) Date of purchase Name and address of dealer Accessories (included) For extra orders, call 1-800-332-5368. PQJXC0301Z (Black) PQJXC0102Z (White) Handset Cord (p. [. . . ] Press (1). If you use "1111" as a PIN code (factory set), there is no need to enter a PIN code. 19). (MUTE) and Indicator Press (PROGRAM). If a wrong PIN code is entered, 3 beeps will sound. Enter a correct PIN code and press (PROGRAM). Advanced Operation Enter the number(s) (1 digit or 2 digits) you want to restrict ((0) to (9)). If you enter a wrong number, enter a correct number. To change restricted digits from 2 digits to 1 digit, press ($) and enter 1 digit. Press (PROGRAM). The unit will return to the standby mode. If your unit is connected to a PBX, this function may not operate. Contact your PBX supplier for more information. To cancel the call restriction Follow steps 1 through 5. In step 6, press ($) to cancel call restriction and press (PROGRAM). A long beep will sound and the unit will return to the standby mode. For assistance, please call: 1-800-211-PANA(7262) 21 Optional Headset Plugging an optional headset into the unit allows a hands-free phone conversation. Please use only a Panasonic KX-TCA87 or KX-TCA90 headset. To order, call the accessories telephone number on page 2. Connecting an Optional Headset to the Unit Connect an optional headset to the headset jack as shown below. The illustration headset is a KX-TCA90. Headset Jack Hook Microphone Earpiece If you want to have a normal conversation, disconnect the headset. 22 Making/Answering Calls Make sure to install the batteries. VOLUME (_), (^) (SP-PHONE/HEADSET) and Indicator 1 2 Press (SP-PHONE/HEADSET) to make or answer a call. The SP-PHONE/HEADSET indicator flashes. If you misdial when making a call, press (SP-PHONE/HEADSET) twice and dial again. To hang up, press (SP-PHONE/HEADSET). The indicator light goes out. To adjust the headset receiver volume (4 levels): While using the headset, press VOLUME (_) or (^). During a conversation using the headset, you cannot switch the call to the handset by lifting it off the cradle. If you disconnect the optional headset during a conversation with the handset on the cradle, the call will be switched to the speakerphone. During a conversation using the speakerphone, you can switch the call to the headset by connecting the headset. For assistance, please call: 1-800-211-PANA(7262) 23 Useful Information Battery Replacement If the speakerphone does not work, it may be the time to replace the batteries. Replace the batteries within 1 minute to keep the programmed settings. + + + - 1 2 1 Disconnect the telephone line cord from the unit. 2 Press down in the direction of the arrow and remove the cover. 3 4 Replace the batteries with new ones using correct polarity (i, j), and close the cover. Connect the telephone line cord to the unit. Battery Precautions: The batteries should be used correctly, otherwise the unit may be damaged by battery leakage. --Do not mix different types of batteries. --Do not charge, short-circuit, disassemble, heat or dispose of in fire. --Remove all the batteries when replacing. Note: --Replace all the batteries once a half year in use of Alkaline batteries, or misoperation may occur. (When you use Manganese batteries, replace all of them once in three months. ) --Do not use nickel-cadmium batteries. 24 Troubleshooting Problem The unit does not work. " Remedy Check the settings (p. Remove the batteries and reinstall them to reset the unit. Check that the dialing mode selection is correct (p. (MUTE) may have been pressed during the conversation. [. . . ] Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ]