User manual PANASONIC KX-TVS50

[. . . ] N Flexible CO Buttons: Used to seize a CO line or perform a feature that has been assigned to the key. O PROGRAM: Used to enter and exit the personal programming mode. P Message/Ringer Lamp: When you receive an intercom call, the lamp flashes green, and on an outside call, the lamp flashes red. When someone has left you a message, the lamp stays on red. Document Version 2008-05 3 Settings Settings Speaker volume While in a hands-free conversation Handset/Headset While using the handset or headset volume*1 Ringer volume LCD Contrast While on-hook PROGRAM AUTO DIAL STORE AUTO DIAL STORE PROGRAM Press Up to increase While on-hook or receiving a call or Down to decrease the volume. Ring Tone (CO) PROGRAM OR INTERCOM Press 2 times. *2 AUTO DIAL PROGRAM STORE LCD Backlight While on-hook Automatic PROGRAM AUTO DIAL Always ON STORE Always OFF AUTO DIAL STORE *1 *2 PROGRAM If you hear your own voice through the handset or headset, decrease the volume. [. . . ] For extra orders for the accessories, call toll-free: 1-800-332-5368 PC connection · Use a straight CAT 5 (or higher) Ethernet cable (not included) that is 6. 5 mm (1/4 in) in diameter or less. · For further information on the connection to a PC, refer to the documentation provided for the PBX. Switching Hub connection AC adaptor · Use a straight CAT 5 (or higher) Ethernet cable (not included) that is 6. 5 mm (1/4 in) in diameter or less. · Use a Panasonic AC adaptor KX-A239 (PQLV206). · The AC adaptor is used as the main disconnect device. Ensure that the AC outlet is located near the unit and is easily accessible. CAUTION: When connecting cables · Ensure that the Ethernet cables and the AC adaptor cord are clamped to prevent damage to the connectors. · Cables may be routed either upwards or downwards by using the appropriate cable clamp located on the back of the unit. When connecting a headset and AC adaptor · Ensure that the headset cord and the AC adaptor cord are wound around the hook to prevent damage to the connectors. 10 Document Version 2008-05 Stand Usage Stand Usage Attaching the Stand Place the catches (A) of the stand into hooks located in the unit. Gently push the stand in the direction indicated until it locks into place. The stand will be mounted in the high position. A Removing the Stand Hold the stand with both hands. Gently rotate the stand in the direction indicated until it is released. Cabling When using the stand, ensure that the cables are clamped as shown. Document Version 2008-05 11 Stand Usage Adjusting from High to Low Position Hold the stand with both hands as shown and gently push the stand in the direction indicated until it locks into the low position (B). Adjusting from Low to High Position Hold the stand with both hands as shown and gently pull the stand in the direction indicated until it locks into the high position (A). A 12 Document Version 2008-05 Wall Mounting Wall Mounting 1. For information on removing the stand, refer to page 11. into the vents or other holes of this unit. Take special care to follow the safety suggestions listed below. Safety 1) The unit should only be connected to a power supply of the type described in the Quick Reference Guide or as shown on the label on the unit. 2) When left unused for a long period of time, the optional AC adaptor should be unplugged from the AC outlet, if you are using Power-overEthernet, disconnect the Ethernet cable. Installation Environment 1) Do not use this unit near water, for example, near a bathtub, washbowl or sink. 2) Keep the unit away from heating appliances and devices that generate electrical noise, such as fluorescent lamps, motors and televisions. These noise sources can interfere with the performance of the unit. It also should not be placed in rooms where the temperature is less than 5 °C (41 °F) or greater than 40 °C (104 °F). Allow 10 cm (3-15/16 in) clearance around the unit for proper ventilation. 14 Document Version 2008-05 Important Information Placement 1) Do not place heavy objects on top of this unit. 2) Care should be taken so that objects do not fall onto, and liquids are not spilled into, the unit. Do not subject this unit to excessive smoke, dust, moisture, mechanical vibration, shock or direct sunlight. 3) Place the unit on a flat surface. WARNING: TO PREVENT POSSIBLE FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. THIS HANDSET EARPIECE IS MAGNETIZED AND MAY RETAIN SMALL FERROUS OBJECTS. [. . . ] When programming emergency numbers and/or making test calls to emergency numbers: 1) Remain on the line and briefly explain to the dispatcher the reason for the call before hanging up. 2) Perform such activities in the off peak hours, such as early morning hours or late evenings. FCC Declaration of Conformity Trade Name: Panasonic Model Number: KX-TVS50 Responsible Party: Panasonic Corporation of North America One Panasonic Way Secaucus, NJ 07094 U. S. A. Telephone No. : 1-800-211-PANA (7262) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Document Version 2008-05 17 Important Information Customer Information This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. [. . . ]