User manual PANASONIC LUMIX DMC-LX2EF

[. . . ] DSC0608027CE B26 Digital Camera DMC-LX2PP DMC-LX2PL DMC-LX2EB DMC-LX2EE DMC-LX2EF DMC-LX2EG DMC-LX2EGM DMC-LX2GC DMC-LX2GD DMC-LX2GK DMC-LX2GN DMC-LX2GT DMC-LX2SG Vol. 1 Colour (S). . . . . . . . . . . Silver Type (except PL/GD/GT) (K). . . . . . . . . . . Black Type (except SG) © 2006 Matsushita Electric Industrial Co. , Ltd. Unauthorized copying and distribution is a violation of law. TABLE OF CONTENTS PAGE 1 Safety Precaution -------------------------------------------------3 1. 1. General Guidelines ----------------------------------------3 1. 2. [. . . ] Yaw direction amplitude error (small) 3000 OIS adj. Pitch direction amplitude error (small) 4000 OIS adj. Yaw direction amplitude error (large) 5000 OIS adj. Pitch direction amplitude error (large) 6000 OIS adj. Yaw direction off set error 9000 OIS adj. Pitch direction off set error A000 OIS adj. Pitch direction gain error C000 OIS adj. Yaw direction position sensor error D000 OIS adj. Pitch direction position sensor error E000 OIS adj. other error Flash 2800 0000 Flash charging error. IC6001-(279) signal line or Flash charging circuit 2B00 0001 EEPROM read error FLASH ROM (EEPROM IC6002 (FLASH ROM) Area) 0002 EEPROM write error IC6002 (FLASH ROM) RTC 2C00 0001 SYSTEM IC initialize failure error Communication between IC6001 (VENUS 3) and IC9101 (SYSTEM) Sub item 15 Attribute SOFT Main item CPU Sub item Reset Card Card Error code High 4 bits Low 4 bits 3000 0001 | 0007 3100 0001 0002 0004 0005 Contents (Upper) Check point (Lower) NMI reset Non Mask-able Interrupt (30000001-30000007 are caused by factors) Card logic error SD card data line or IC6001 (VENUS 3) Card physical error SD card data line or IC6001 (VENUS 3) Write error SD card data line or IC6001 (VENUS 3) Format error SD card data line or IC6001 (VENUS 3) Camera task finish process time out. Communication between Lens system and IC6001 (VENUS 3) Camera task invalid code error. IC6001 (VENUS 3) File time out error in recording motion image IC6001 (VENUS 3) File data send error in recording motion image IC6001 (VENUS 3) Single or burst recording brake time out. FLASHROM processing early period of camera during movement Not complete zoom lens processing Zoom lens Dummy processing = Injustice command (0-7bit : command, 8-15bit : Status) Though record preprocessing is necessary, it is not called Though record preprocessing is necessary, it is not completed CPU, ASIC hard Stop 3800 0001 0002 0100 0200 0300 0000 0000 0000 0000 0000 Operation Zoom Power on Zoom 3B00 3C00 3500 3501 3502 · 5. How to returned to Normal Display: Turn the power off and on, to exit from Error code display mode. NOTE: The error code can not be initialized. 16 6. 2. Confirmation of Firmware Version The Firmware version can be confirmed by ordering the following steps:. The temporary cancellation of factory setting: Set the mode dial to "[ P ]". Insert the SD memory card which has a few photo data. While keep pressing [ Optical Image Stabilizer ] and "[ UP ] of Cross key" simultaneously, then turn the power on. Confirm the version: Set the mode dial to "[ Playback ]" and then press [ DISPLAY ] to switch to LCD with indication. A) Press [ Optical Image Stabilizer ] and "[ DOWN ] of Cross key" simultaneously. (No need to keep pressing. ) (The version information is displayed on the LCD with light blue colour letters. ) (Fig. [. . . ] Unless otherwise specified, All resistors are in OHMS, K=1, 000 OHMS. All capacitors are in MICRO-FARADS (uf), P=uuF. The marking (RTL) indicates the retention time is limited for this item. After the discontinuation of this assembly in production, it will no longer be available. E. S. D. [. . . ]