User manual PANASONIC MC-UL674

[. . . ] REMINDER FOR CUSTOMER The model and serial number of the product may be found on the nameplate located at the back of your vacuum cleaner. You should note the model and serial number in the spaces provided and retain this book for future reference. Model Number: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial Number:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Date Purchased: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Remove dust accumulated or replace the filters. (see DUST BIN FILTER CHANGING AND CLEANING) · If exhaust filter is full of dust replace it. (see EXHAUST FILTER MAINTENANCE) · If there is a blockage, remove it. (see BLOCKAGES) 2 1 · Mains plug fuse. (UK, IRL only) Push mains lead into mains lead clip in back of vacuum cleaner. Plug the polarized mains lead into a 240V mains located near floor. · Thermal cut-out device may have operated. · Hose inlet is blocked. · Check dust mark. · Primary filter 3 1 To prevent injury or damage, hold plug head while rewinding mains lead. Push mains lead retract pedal down to rewind. · Check hose is properly inserted to the suction pipe inlet. · Check dust accumulated on primary filter. · Dust bin inlet is blocked. E) ON/OFF SWITCH On-Off Switch Agitator does not rotate. · Clogged by a large object in the agitator housing. · Belts broken or loose. · If there is any obstruction, remove it. · If the belt is broken, replace it. If loose re-install it. THERMAL CUT-OUT This vacuum cleaner is fitted with a thermal cut-out device which automatically turns off the vacuum cleaner to prevent overheating of the motor. When this happens, disconnect the vacuum cleaner from the mains socket and check the dust bin and filters as it may be full or clogged with fine dust. To start or stop the vacuum cleaner, push the switch button to `I' to turn ON and to `O' to turn OFF. To start or stop the agitator, push the carpet / bare floor switch button to `I' to turn ON and to `O' to turn OFF. After emptying the dust bin or removing the obstruction, leave the vacuum cleaner to cool down until the thermal cut-out resets after approximately 40 minutes. IMPORTANT: The thermal cut-out will not reset if the vacuum cleaner is not disconnected from the mains socket. F) HANDLE LOCK / RELEASE BY FOOT PEDAL 1 2 1 CAUTION: To prevent damaging carpeted floors, tiled floors, linoleum, etc. Do not leave the agitator rotating in the same place for too long. NOTE: After use, unplug from the mains and store the vacuum cleaner in the upright position. MAINS LEAD IMPORTANT: If the mains lead becomes damaged, it must be repaired by Panasonic, authorised service centre or a qualified person in order to avoid any hazard. Release the handle by pressing down on the foot pedal with your foot and pulling back and down on the handle with your hand. Use low position for cleaning under furniture. To move the vacuum cleaner to the low position press the foot pedal again. -6- - 15 - H) BLOCKAGES 1 G) HOW TO USE THE ACCESSORIES The hose located on the vacuum cleaner carries the dirt from the nozzle up to the dust bin. [. . . ] Failure to do so can result in personal injury. 2 1 Carefully remove any residue that may exist in the belt area. Dust Bin Lid Lid Release Lever TO REMOVE BELT/CLEAN AGITATOR Belt Position hands on the agitator. If the belt is still attached to the agitator, there will be tension on it. Carefully lift the left end (belt side) of the agitator and then lift the right end. Remove the worn or broken belt from the pulley or motor drive shaft. TO EMPTY DUST BIN Hold dust bin over a trash container. Press the dust bin lid release lever. [. . . ]