User manual PANASONIC NN-CT552W

[. . . ] 4 PARTS IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 HOW TO ASSEMBLE YOUR VACUUM CLEANER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 A) Handle Assembly / Hose Assembly / Mains Lead Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 * * * * * * B) Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Do not run the vacuum cleaner over tassels or fringes of rugs or mats as they could get caught up in the beater bar and may cause damage to the brush and belt. 3. Keep the vacuum cleaner away from heat sources such as radiators, fire, direct sunlight, etc. 4. To avoid damaging the machine, never let the vacuum cleaner pick up wet matter, mud, burning ashes or large and sharp objects. 5. Do not pull on the mains lead when disconnecting the appliance from the socket outlet, always pull on the plug body itself. 6. To avoid injury keep your fingers and hand away from the beater bar and never put them at the exhaust area. 4 PARTS IDENTIFICATION Dust Bin Handle Filter Refresher Lid Buckle HEPA Filter Unit Mini Turbine Nozzle Handle Upper Cord Storage Hook Hose Dust Bin Dust Bin Plate Latch Mains Lead Hook Mains Lead Filter Cover Overload Protection Reset Button Furniture Guard Nozzle Beater Bar (inside) Belt (inside) Foot Pedal (Handle release) Pre-Filter Cord Clip Crevice Hose Hose Hook ON/OFF Switch Floor/Carpet Selector Lower Cord Storage Hook (Carrying Handle) Crevice Extension Wand Dusting Brush Extension Wand (Additional 1 pc only for NN-CT552W) Connection Pipe Suction Inlet Air Protector Floor Nozzle (Only for NN-CT552W) Foot Pedal (Handle release) Extension Wand Holder Curved Wand Curved Wand Holder Nozzle Hose 5 HOW TO ASSEMBLE YOUR VACUUM CLEANER A) HANDLE ASSEMBLY / HOSE ASSEMBLY / MAINS LEAD STORAGE Tape Connection Pipe Hook OF F FLO OR CA RP ET Crevice Suction Inlet Mini Turbine Nozzle 1. Remove tape and screw from the body. 2. Insert the base of the handle into the top of the vacuum cleaner body as shown. IMPORTANT: Do not overtighten the screw. 3. Insert the connection pipe to suction inlet. Ensure that the 2 hooks of the connection pipe are completely fitted into the suction inlet. Dusting Brush Extension Wand Hose Hook Upper Cord Storage Hook Extension Wand Holder Curved Wand Holder Curved Wand Curved Wand Holder Lower Cord Storage Hook / Carrying Handle 4. Set the hose around the hose hook and insert the curved wand to the curved wand holder. 5. Make sure you hear a “click” sound to indicate that the dust bin plate is fully latched. 10 • Clean up outer dust bin with clean, soft cloth that has been dipped in water and wrung dry. • Place dust bin back into vacuum cleaner by inserting the bottom first and tilting back. • Push forward and lower dust bin handle to lock dust bin in place. NOTE: • A lid holding bracket is located on the hinge area of the dust bin. • This bracket may release in order to prevent damage to the dust bin or the dust bin plate due to the dust bin was dropped or the dust bin plate getting any impact. Lid Holding Bracket Hinge • To reassemble, put the hinge of the dust bin plate to its original location as shown. • Slide the lid holding bracket to its original location as shown and push until you hear a “click” sound. NOTE: • Push the lid holding bracket using both palm if the lid holding bracket is difficult to push in. 11 MAINTAINING THE HEPA FILTER UNIT Lid Pull to release Pull to release • Check HEPA filter unit frequently and clean when dirty. • Remove HEPA filter unit from dust bin by pulling both buckle as shown. • Clean HEPA filter unit by gently tapping over a rubbish container. Tap on Lid several sides to ensure best cleaning. DO NOT clean the HEPA filter unit by brush or clean it with water. • Reinstall the HEPA filter unit as per reverse procedure. HEPA Filter Unit Buckle Dust Bin TO CLEAN THE PRE-FILTER • Remove HEPA filter unit from dust bin. Refer to maintaining the HEPA filter unit (as above). • Press the latch to open the dust bin plate. [. . . ] Review this chart to find do-it-yourself solutions for minor performance problems. Any service needed, other than those described in these Operating Instructions, should be performed by an authorised service representative. PROBLEM Vacuum Cleaner won’t run. Poor job of dirt pick-up. POSSIBLE CAUSE 1. Unplug vacuum cleaner, allow to cool and thermal protector will reset itself. [. . . ]