User manual PANASONIC NV-GS33EGE

[. . . ] R Operating Instructions Instrukcja obslugi Digital Video Camera Model No. NV-GS22EGE NV-GS33EGE Before use, please read these instructions completely. Przed pierwszym wlczeniem kamery prosimy o dokladne przeczytanie instrukcji obslugi. VQT0H63-1 Information for Your Safety As this equipment gets hot during use, operate it in a well-ventilated place; do not install this equipment in a confined space such as a bookcase or similar unit. To reduce the risk of fire, electric shock or product damage, do not expose this equipment to rain, moisture, dripping or splashing and ensure that no objects filled with liquids, such as vases, shall be placed on the equipment. AC Adaptor The rating plate is on the underside of the AC Adaptor. use, recording of certain material may be restricted. [. . . ] When the digital effect is paused temporarily, the selected effect's indication flashes. To Cancel the Digital Effect Press the [SELECT] Button (59) on the Remote Controller and clear the digital effect indication. [S-VIDEO IN] [VIDEO IN] [AUDIO IN] 2 1 ª Wipe Mode and Mix Mode 1 Press the [1] Button (72). (72) V S-VIDEO OUT /REW PLAY FF/W REMOTE/MIC A/V OUT PHONES sV DV 6 1 5 W (PLUG IN POWER) STILL ADV PAUSE STILL ADV E INDEX K S C ; STOP D INDEX L P. B. ZOOM -31- Connect to the TV with the AV Cable 1, make a connection with the TV. If the TV has an S-Video Socket, connect the S-Video Cable 2, too. Playback Mode When plugging the pin plug of the AV cable into the [A/V OUT] Socket, plug it in as far as it goes. To Make the Indications Appear on the TV Screen Press the [OSD] Button (51) on the Remote Controller. (51) OSD DATE/ TIME PHOTO SHOT START/ STOP DISPLAY RESET TITLE ZOOM For other notes concerning this item, see -39-. -32- Editing Mode Editing Mode Audio Dubbing You can add music or narration to the recorded Cassette. If the tape recorded in the [16bit] Mode is dubbed with the Audio Dubbing function, the original sound is erased. (If you wish to preserve the original sound, use the [12bit] Mode when recording. ) Audio Dubbing cannot be performed on a recording made in LP Mode. (-15-) 1 Press the [;] Button (69) on the Remote Controller where you want to add new sound. sVOL r Copying on an S-VHS (or a VHS) Cassette (Dubbing) After connecting the Movie Camera and the VCR as illustrated, start the following procedures. [S-VIDEO IN] [VIDEO IN] [AUDIO IN] MULTI/ P-IN-P V T ¥REC A. DUB FF/W (55) W 2 /REW PLAY 1 6 1 5 STILL ADV PAUSE STILL ADV E INDEX K SELECT ; STOP D INDEX L P. B. ZOOM (69) S-VIDEO OUT 2 Press the [A. DUB] Button (55) on the Remote Controller. 3 To start Audio Dubbing, press the [;] Button (69) on the Remote Controller. REMOTE/MIC A/V OUT PHONES DV (PLUG IN POWER) To Cancel Audio Dubbing Press the [;] Button (69) on the Remote Controller. The Movie Camera is in the Still Playback Mode again. To Play Back the Sound Recorded by 12bit Audio Dubbing Set [TAPE PLAYBACK MENU] >> [PLAYBACK] >> [12bit AUDIO] >> [ST2] or [MIX]. ST1: It plays back only the original sound. ST2: It plays back only the sound added by Audio Dubbing. MIX: It plays back both the original sound and the sound added by Audio Dubbing simultaneously. To Dub Audio While Listening to a Pre-recorded Sound When pausing the audio dubbing, set the [12bit AUDIO] on the [PLAYBACK] Sub-Menu to [ST2] and you can check the pre-recorded sound. Use headphones to listen to the pre-recorded sound while dubbing the audio. For other notes concerning this item, see -39-. 1 AV Cable 2 S-Video Cable Be sure to press the [OSD] Button (-6-) on the Remote Controller prior to copying so that no indications are visible. Otherwise, the displayed tape counter and function indications are also copied. Movie Camera: 1 Insert the recorded Cassette. VCR: 2 Insert an unrecorded Cassette with an erasure prevention tab. If various setups (such as external input, tape speed, etc. ) are required, please refer to the operating instructions of your VCR. Movie Camera: 3 Press the [1] Button to start playback. 5 Press the Pause or Stop Button to stop recording. [. . . ] The Time Code is automatically recorded as a part of the sub-code at each recording. When a new (previously unrecorded) Cassette is inserted, the Time Code automatically starts from zero. If a recorded Cassette is inserted, the Time Code picks up from the point where the last scene was recorded. (In this case, when the Cassette is inserted, the zero display [0h00m00s00f] may appear, but the Time Code starts from the previous value. ) The Time Code cannot be reset to zero. [. . . ]