User manual PANASONIC NV-GS400EB

[. . . ] Operating Instructions USB Connection Kit Before use, please read these instructions completely. VQT0K53 Before opening the CD-ROM package, please read the following. End User License Agreement (for USB Driver, Video Stream Driver, SD Viewer and MotionDV STUDIO) You ("Licensee") are granted a license for the Software defined in this End User Soft Agreement ("Agreement") on condition that you agree to the terms and conditions of this Agreement. If Licensee does not agree to the terms and conditions of this Agreement, promptly return the Software to Matsushita Electric Industrial Co. , Ltd. ("Matsushita"), its distributors or dealers from which you made the purchase. Article 1 License Licensee is granted the right to use the software, including the information recorded or described on the CD-ROM, instruction manuals, and any other media provided to Licensee (collectively "Software"), but all applicable rights to patents, copyrights, trademarks and trade secrets in the Software are not transferred to Licensee. [. . . ] The [Setup Menu] Screen appears. 3 Click [USB Driver]. The set up program starts running. 4 Finish installation by following the on-screen instructions. Click [Next] and proceed with installation. Applications which are compatible with older version of DirectX may not operate properly by installing DirectX 9. 0b. In this case, consult the manufacturers of the applications disabled. 2 1 Insert the supplied CD-ROM (Disc 2) into the personal computer's CD-ROM drive. 2 Click [Next]. After reading the displayed contents, please carry out the installation according to instructions. 3 Select the Video System. 4 After the completion of setup, click on [Finish]. 3 Sample data is installed concurrently with the MotionDV STUDIO 5. 1E LE software. 5 Click [Finish] when the [Restarting Windows] Dialogue appears. Reboot the computer to finish installing MotionDV STUDIO. 4 10 3 Connecting the Movie Camera to Personal Computer When you use a personal computer, use of the AC Adaptor is recommended for the power supply of the Movie Camera. 4 ª Confirmation before connection (for Windows XP/2000) When you connect the personal computer and the Movie Camera with the USB connection cable and then use MotionDV STUDIO on Windows XP (SP1 or later) or Windows 2000 (SP4 or later), check the driver of the USB host controller. It is required to use the driver for which [Microsoft] is displayed on [Driver Provider] in [Driver] tab. 1 1 Select [Start] >> [Settings] >> [Control Panel] to start [System]. [System Properties] is displayed. 2 Click [Hardware] tab and then click [Device Manager]. 3 Right-click [Enhanced Host Controller] etc. in [Device Manager] and then select [Properties]. The indication [Enhanced Host Controller] is changed as [EHCI] depending on the host controller you use. 4 Click [Driver] tab to check the description on [Driver 2 Provider]. If [Microsoft] is displayed on [Driver Provider], the confirmation procedure is completed. If a description other than [Microsoft] is displayed Update the driver with the following procedure. 1 Click [Update Driver. . . ]. 2 Check [Install from a list or specific location (Advanced)] and then click [Next]. 3 3 (When your OS is Windows XP) When your OS is Windows 2000, click [Next] after [Update Device Driver Wizard] appears. Check [Don't search. I will choose the driver to install] and then click [Next]. (When your OS is Windows 2000) Check [Display a list of the known drivers for this device so that I can choose a specific driver] and then click [Next]. 4 Click [Standard Universal PCI to USB Host Controller] and then click [Next]. 5 Click [Finish]. The update of the driver is completed. Connect the Movie Camera. 4 11 ª For Using SD Viewer 3. 1E When your OS is Windows 98SE, Install USB Driver before connecting. Never connect the USB Connecting Cable until the USB Driver is installed. 1 Insert the Memory Card into the Movie Camera. 2 Set the Movie Camera to PC Accessing Mode. 3 Connect the Movie Camera to Personal Computer 1) with auxiliary USB Connection Cable. It enters PC Accessing Mode. 4 Start SD Viewer 3. 1E. (l 14) 2) 1) USB Connection Cable 2) USB terminal To copy the data from the memory card to a personal computer using Explorer, etc. instead of SD Viewer 3. 1E, set the Movie Camera to PC Accessing Mode and insert the card. 12 ª For Using MotionDV STUDIO 5. 1E LE If you wish to capture data from a tape, set the Movie Camera to Tape Playback Mode and insert the tape. If you wish to capture images from the lens of the Movie Camera, set the Movie Camera to the Tape Recording Mode and remove the tape and the card. With USB Connection Cable (supplied) 1) OS: Windows XP SP1 or later Windows 2000 SP4 or later The personal computer should be compatible with USB 2. 0 Hi-Speed. 1 Set the Movie Camera to Tape Playback Mode or Tape 2) Recording Mode. 2 Set [PLAYBACK] or [CAMERA] >> [USB FUNCTION] >> [MotionDV]. 3 Connect the Movie Camera to Personal Computer with auxiliary USB Connection Cable. 4 Start MotionDV STUDIO 5. 1E LE. (l 14) You cannot record the video edited by the PC onto the Tape in the Movie camera. 1) USB Connection Cable 2) USB terminal With DV Cable (optional) OS: Windows Me/2000/XP 1 Set the Movie Camera to Tape Recording Mode or Tape Playback Mode. 2 Connect the Movie Camera to Personal Computer with auxiliary DV Cable. 3 Start MotionDV STUDIO 5. 1E LE. (l 14) 1) You can record the video edited by the PC onto the Tape in the Movie camera. [. . . ] Enter the following paths to complete the connection: If the message "MTDV98M3. pdr is not found" is displayed, enter "C:\WINDOWS\system\IOSUBSYS". If the message "MTDV98M3. sys is not found" is displayed, enter "C:\WINDOWS\system32\DRIVERS". (The paths will differ depending on the environment of your personal computer. ) When the Movie Camera is switched to the PC Accessing Mode while it is connected to the personal computer, the operation mode of the Movie Camera cannot be switched. In this case, disconnect the USB Connection Cable. [. . . ]