User manual PANASONIC NV-SD260B

[. . . ] 5 Setting the Remote Control to Operate Your TV . . . . . . . . . . . . . . . . 6 Advanced Operations Search Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 To Quickly Find the Beginning of a Desired Programme (VISS=VHS Index Search System) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 To Search for a Desired Programme While Checking the Recorded Contents on a Cassette (Intro-Jet Scan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Opearations 1 Press the SEARCH button M to display the Programme List menu. 2 Programme List Pos 2 3 Name ZDF ARD Date Start 27/10 We 17:46 28/10 Th 15:00 Start Stop SP VPS ON OFF LP PDC Min ON ON jjj 27/10 We 20:00 21:30 SP 30/10 Sa 19:00 20:00 LP jj/jj jj jj:jj jj:jj jj jj jj jj jj 90 60 jjj ZDF jjjjj jjjjj jjjjj jjjjj Su-Sa jj/jj jj jj jj jj jj jj jj jj jj jj 17:30 18:00 LP jj:jj jj jj jj jj jj jj jj:jj jj jj jj jj jj jj ON jjj jjj jjj jjj 30 jjj jjj jjj jjj Notes for Cancelling the Programming of a Timer Recording In some cases, for example as listed below, the programming of a timer recording remains stored in the memory until 4 a. m. When a timer recording was not performed up to the TV programme's ending time because the remaining tape time was not sufficient. When you have stopped the timer recording while it was being performed. To Check the Total Timer Recording Programming Time jjjjj jjjjj jjjjj jjjjj jjjjj jjjjj jj jj jj/jj jj/jj jj/jj jj/jj jj/jj jj jj jj jj jj jj Press the Cursor buttons (34) Q to select the programme that you want to locate and play back. Press the SEARCH button M to start the search for the beginning of the selected programme. After the desired recorded programme has been found, playback starts automatically. If, after playback has started, you want to search for the beginning of the same or another programme, press the SEARCH button M. Playback stops, and the Programme List menu appears. Repeat the above operations steps 2 ­3. To Cancel the Programme List Search: Press the EXIT button R. Hints: When you press the SEARCH button M in the operation step 1, the last timer-recorded programme is selected (highlighted). If you take out the cassette or insert another cassette after a timer recording has finished, pressing the SEARCH button M activates the Intro-Jet Scan instead of the Programme List Search. Conditions for correct operation of the Intro-Jet Scan function: The cassette must have been ejected after the timer recordings were performed. VCR must be switched on, be in the playback mode or be in the standby mode. Each programme recorded on the tape must be at least 15 minutes long. Preparations Display the VCR picture on the TV. Operations 1 Press the SEARCH button M to start the Intro-Jet Scan. After rewinding the tape to the beginning, the VCR plays it back at high speed for approximately 10 seconds. It then fast-forwards the tape to the next tape position marked by an index signal (beginning of a programme), and every time an index signal is found, the VCR switches over to high-speed playback (Cue) for about 10 seconds. Beginning of tape Index signal Programme 1 Rewinding High-speed Playback (Cue) Fast-forwarding Programme 2 Present tape position Programme 3 2 When you have found the programme that you want to view, press the Play button I to start normal playback. To Cancel the Intro-Jet Scan or to Stop Playback: Press the Stop button 9. Note: If you press the SEARCH button M after a timer recording has finished, but before ejecting that cassette, the Programme List Search (for details, see page 21) will be activated instead of the Intro-Jet Scan. 22 Editing Assemble Editing The assemble editing function makes it easy to record the picture and sound of virtually any number of scenes or programmes in succession. Assemble editing from an external source, for example from a video movie camera, can be performed in the same way. Recording unit (this VCR) Front Rear 5 When that point is reached, press the Pause/Slow button 7 again to start recording the new picture and sound from the playback unit. To record (copy) additional scenes, press the Pause/ Slow button 7 to put this VCR in the recording pause mode and then perform steps 4 and 5 again. At the point where you want to stop recording, press the Stop button 9 to finish recording. 6 7 ] ^ f g Video movie camera Other VCR Note: If you leave the VCR in the recording pause mode for more than 5 minutes in step 3 or 6, the VCR automatically switches over to the stop mode to protect the video heads. Preparations Connect a video movie camera or a VCR to this VCR with an audio/video cable or a 21-pin Scart cable, as shown in the illustration. [. . . ] Avoid magnets or magnetized objects Never bring a magnet or magnetized object close to the VCR because this could adversely affect the performance of the VCR. When using the VCR together with other equipment, keep as much distance as possible between them to prevent them from adversely affecting each other's performance. No fingers or other objects inside Touching internal parts of the VCR is dangerous, and may seriously damage it. There are no user serviceable parts inside. [. . . ]