User manual PANASONIC NV-VP31EBEBL

[. . . ] NV-VP31EB/EBL DVD/CD Player / Video Cassette Recorder (Model suffix: 'EB' for UK model, 'EBL' for Ireland model) Operating Instructions DVD/CD PLAYER OPEN / CLOSE EJECT PULL-OPEN MUSIC WITH PICTURE AV ENHANCER 2. 0 DIGITAL OUT NV-VP31 PAL Safety Precautions 2-3 Included Assessories / Sales and Support Information 4 Remote Remote Control - Codes / Inserting batteries 5 Front Panel / Sockets 6-7 Remote control functions 8-10 Connecting with 21-pin Scart cable 11 Connecting with Audio-Videocable 12 VCR Auto Setup 13 Connecting with RF cable 14-15 VCR Auto Setup with RF cable 15 Connecting to Satellite Receiver, Set Top Box 16-17 DVD-Connectors 18 Checking the Settings after Auto Setup 19 Removing Interference / Changing RF-output channel 20 VCR menu control 21 VCR Playback / Tracking control 22-23 General convenient functions / Tape Care 24-25 Recording 26-32 Timer recording 27-28 Recording with INTELLIGENT TIMER 29 Recording with VIDEO Plus+ 30-31 Recording with external recording controls 32 Manual Functions 33-39 Manual Tuning 33 Changing the name of TV stations 34 Changing the order of TV stations or deleting a station 34 Creating a new station table 35 Shipping condition / factory defaults 35 Others menu / Owner ID 36-37 Clock setting / NICAM sound system 38-39 DVD-QUICK SETUP DVD Playback functions VCR-DVD functions Navigation Menu HighMAT / CD Text DISPLAY menu SETUP menus Information Country codes Before requesting service Specifications Index Contents Page Before connecting the device, operating it or adjusting settings please read these operating instructions completely; especially the safety precautions on pages 3. 40 41-46 47 48-49 50 51-53 54-55 56-57 58 59-61 63 last page Important Safety Warnings ! The moulded three pin mains plug is supplied for your safety and convenience and must NOT be cut off. A 5 amp fuse is fitted in the mains plug. If the fuse has to be replaced, it must be of the same rating and approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. [. . . ] With select the Tuning menu, confirm with ENTER. With select [Auto Setup], confirm with ENTER. Press ENTER to confirm. The Auto Setup menu will be displayed. The Automatic Tuning will start. D D Auto Setup Tuning : Ch 1 When no stations have been set, confirm all connections and restart Auto Setup. You can restart Auto Setup, without using remote controller, by pressing some buttons on the front of the unit. Hold down and on the main unit simultaneously for about 5 seconds. Tuning Manual Auto Setup Shipping condition Owner ID OK? ENTER : yes EXIT : no Shipping condition/factory defaults Shipping condition resets the VCR back to the original factory settings except Owner ID information. This is useful if the VCR is going to be used in a new location as auto-setup will begin again when the unit is switched on (after connecting to aerial and mains). With select the Tuning menu, confirm with ENTER. With select [Shipping condition] and confirm with ENTER. Press ENTER to confirm. ! To re-tune the VCR, disconnect and reconnect the AC Mains lead. 35 Manual Functions Menu Others VHS DVD Tape length AV2 SQPB Sets the tape length of the cassette you use. AUTO ( E - 240), E - 195, E - 260, E - 300 Selects the type of external unit connected to the VCR/DVD's AV2 socket. EXT : If another video recorder or satellite receiver is connected. AUTO ON OFF 4:3 WIDE OFF AUTO : The VCR automatically detects the type of recording. : Plays back S-VHS format cassettes in quasi S-VHS format. : Plays back cassettes recorded in VHS format only. : Displays appear at the edge of the screen displays not visible on 16:9 format screens). : Displays appear at the edge of the screen (displays appear in the middle on 4:3 format screens). ! Press MENU Select Others Confirm with ENTER Select the Menu item Changes with Press MENU to quit the menu. Others Tape length :AUTO ( E-240) AV2 :NORMAL SQPB :AUTO OSD :4 : 3 VCR/DVD OUTPUT:AUTO Remote :VCR 1 EXT LINK :1 OSD VCR/DVD OUTPUT : When you press a function button the unit will activate the relevant video or DVD output, depending on the setting of the VCR/DVD toggle switch. MANUAL : Press the VCR/DVD OUTPUT button to manually toggle between the video and DVD outputs. The device and the remote control may be switched to alternative frequencies. In the Menu select VCR1 or VCR2 to switch the device settings. Then press and hold the ENTER and 1 or 2 keys of the remote control, to switch it to the according device frequency. Remote EXT LINK 2 : External recording control by satellite receivers or digital receivers (video signal). 1 : For digital receivers transmitting a special recording control signal, e. g. [. . . ] ! 60 Before requesting service DVD DISTORTIONS The loudspeakers emit loud noise: The message "NO PLAY" appears: The OSD displays are cut off along their top edge: The player does not respond to function key commands: Playback does not start after pressing PLAY: Unable to change the audio track or the subtitle language: The subtitles are not shown: The audio track or subtitles do not use the language selected from the menu: Unable to change the aspect angle: You forgot your password: !! Go to the Setup screen and check the Audio menu settings of Dolby Digital, DTS Digital Surround and MPEG. The player cannot play discs of the current format. Certain control operations are not available with some discs. [. . . ]