User manual PANASONIC NV-VS40

[. . . ] After Automatic tuning has finished, press EXIT. - While Auto Setup is running the first digit of the VCR display will flash. After a while it will stop flashing and the RF output channel number will be displayed. - Select an unused channel pre-set on your TV and tune it to the RF output channel number shown on the VCR display (or until you can clearly see the Auto Setup screen). [. . . ] To set the Owner ID now, press the Numeric buttons or to enter a four-digit PIN number. Make sure that you will remember the PIN number (make a note of it). Press the ENTER button twice to confirm. Enter the [Name], [House No] and [Postcode] in the same way. Press the ENTER button to confirm each entry. Press the EXIT button to leave the Owner ID screen. Optionally, you can have a QUICK SETUP following VCR Auto Setup for the DVD player (page 6). Clock / Zeit Datumset MANUAL If the clock setting menu appears !05 (Auto clock set was not possible due to a weak signal) Press to set the correct time and date. Press the ENTER button to finish this setting. D Mind that a wrong date or time will influence the programmed recording of TV programmes (don't forget to change summer time and winter time). -2- Connecting with 21-pin Scart cable (Fully wired) 2 Aerial AV1 21-pin Scart socket AC IN~ AC IN RF IN Aerial input Follow the steps described below. 1 Ensure TV Power is disconnected from AC Mains socket. VCR / DVD DVD/VHS COMMON OUT O COMPONENT VIDEO OUT VI ED (PROGRESSIVE/ INTERLACE) PB L Y L RF IN AV1 (TV) DVD OUT AUDIO AUDIO AV2 (EXT) RF OUT 2 Connect aerial to the RF IN (Aerial input) connector of the VCR/DVD. R PR COAXIAL DIGITAL AUDIO OUT R RF OUT Aerial output 3 Connect the VCR/DVD´s RF OUT (Aerial output) to the TV set's Aerial in connector. 5 AC mains lead 4 Connect the VCR/DVD's AV1 socket TV 4 21-pin Scart cable (21-pin Scart socket) to the TV set's Scart In socket. 5 Connect VCR/DVD and TV set to 1 AC mains socket Aerial input the AC mains socket. Follow the steps for VCR Auto Setup. 5 AC mains lead 3 RF coaxial cable VCR Auto Setup with 21-pin Scart cable (Automatic tuning) Auto Setup !! : Ch 21 VCR Display Tuning ! Turn on your television set. If station name is [ ]: The asterisks indicate that a station was found during Auto Setup but has not been named (due to weak signal). The stations in the list with asterisk will need to be named manually see page 34 of Operating Instructions. If station name is [- - - -]: The dashes represent unused channel positions. The stations in the list with dashes will need to be set manually. Press the EXIT button to exit the On Screen Display. EXIT :select : exit ENTER : access D Tuning Manual Auto Setup Shipping condition Owner ID D MENU : select : return ENTER EXIT : access : exit EXIT ! When the station names and/or channel numbers have not been set correctly, see page 34 of Operating Instructions for details. When no station has been found, confirm all connections of the VCR again and restart the Auto Setup. See page 35 of Operating Instructions for details. TV Reception Channels Tuning Tuning Ch 22 23 24 25 26 Pos Name 6 7 ---8 ---9 ---10 - - - Ch 30 --------Pos 1 2 3 4 5 Name RTE1 NET2 TNG BBC1 BBC2 Ch 2 4 6 22 23 Pos Name 6 ITV 7 CH4 8 CH5 9 ---10 - - - Ch 24 25 26 ----Pos 1 2 3 4 5 Name BBC1 BBC2 ITV CH4 CH5 The reception channels are different for UK and Ireland. Example of UK model Example of Ireland model -4- Removing Interference / Changing RF-output channel In some cases, interference (lines or patterning) or a very poor picture may appear on the TV when the VCR is connected. If this happens, follow the steps below to change the video playback channel (RF output channel) to remove the interference. TV screen The picture with interference VCR Ch:28 MENU ! Press the MENU button for more than 5 seconds. The RF output channel number is displayed on the VCR display. On-Screen Display Test pattern indication VCR display TRACKING/V-LOCK ! Indication when the RF output channel is 28 (example) CH Press the Numeric buttons or use the Channel (CH) button to select a channel number, which differs by 2 or 3 from the present channel number. (For example, if the original channel number was 28, enter 31. ) 8 9 Indication after changing the RF output channel to 31 (example) VCR Ch:31 ! Retune your TV until you receive the Test pattern. It may be necessary to repeat steps above until you can see the Test pattern clearly. [. . . ] Press SETUP to quit the menu. Select the menu language. English Deutsch Español Svenska Français Italiano Polski Nederlands to select and press ENTER RETURN to return DVD QUICK SETUP may follow VCR Auto Setup. VHS DVD !! Use the remote control's VHS/DVD function to select DVD. Press SETUP to display the QUICK SETUP menu. [. . . ]