User manual PANASONIC NV-VX44B

[. . . ] Refer servicing to qualified service personnel. ! !"#$%&'()*+ !" !"#$%&'()*+, !"#$%&'()*+, *-#. /01234 !"#$%&'()*+, -. /0123456 Movie Camera The rating plate is on the underside of the Movie Camera. AC Adaptor !"#$%&'()*+"#, -. /0 !"#$%&'()*+, -. /012-. 34567 !"#$%!&'()* +, !"# $%&'()*+, -ksJspRM ksJspTM !"#$%&'(#)*+, -. /012345678 !"#$%&'( The rating plate is on the underside of the AC Adaptor. As this equipment gets hot during use, operate it in a well ventilated place; do not install this equipment in a confined space such as a bookcase or similar unit. Carefully read the Operating Instructions and use the Movie Camera correctly. Injury or material damage resulting from any kind of use that is not in accordance with the operating procedures explained in these Operating Instructions are the sole responsibility of the user. These Operating Instructions are for the two Movie Camera models NV-VS50 and NV-VS70. Please note that the actual controls and components, etc. [. . . ] The [WIPE] or [MIX] Indication appears. 2 3 4 !" L !" L !"#$%&'( !"#$%& Press the Recording Start/Stop Button to start recording normally. Press the Recording Start/Stop Button to stop recording the scene. The last picture is stored in memory. The [WIPE] or [MIX] Indication changes to [B] or [C]. !"#$%&'()*+, xtfmbz xjfuz !"xBz xCz !" L !"#$% !"#$%&'( &'()*+, -#!". /01 !!"xbccb`qNz !"#$%&' xafdfq^i=bccb`qz xlccz 4 Press the Recording Start/Stop Button to start recording the next scene. The last picture of the previous scene is gradually replaced by the new scene. !"#$%&'()*+, -. / 01$%&'() !"#$%&'(&'#)*+ !"#$%&'()*+, -. /01234(5*6 !"#$% !& Cancelling the Mix or Wipe Function Set [EFFECT1] on the [DIGITAL EFFECT] Sub-Menu to [OFF]. All subsequent scene-to-scene transitions will be recorded with this Mix or Wipe Effect until you cancel the Mix or Wipe Function. The Negative and Solarisation Effects cannot be applied to a picture stored in the digital image memory for the Mix or Wipe Function. -96- 1 D. FADE1 BLK CAMERA VCR INFOWINDOW 1 2 D. FADE1 BLK D. FADE1 BLK PROG. AE STORE COLOUR OFF/ON D. FADE2 WHT D. FADE2 WHT D. FADE2 WHT 2 1 MENU MF/ TRACKING CAMERA OFF VCR 3 D. FADE3 BLK D. FADE3 BLK D. FADE3 BLK FADE FOCUS / SET 4, 7 2, 3, 5, 6, 8 ENGLISH !"# P !"#$%&'() !P xaKc^abPz Digital Fade There are 3 Digital Fade Modes available. 1 2 3 1 Digital Fade 1 [D. FADE1] 2 Digital Fade 2 [D. FADE2] 3 Digital Fade 3 [D. FADE3] !!" x aKc^abN z x aKc^abP z O 1 xafdfq^i=bccb`qz x bccb`qO z O x aKc^abO z N !l TU P xz ! 1 !" ! Set [EFFECT2] on the [DIGITAL EFFECT] SubMenu to [D. FADE1], [D. FADE2] or [D. FADE3]. (l 78) The [] Lamp lights. 2 2 !x c^abz !Although you can select a digital effect on the [DIGITAL EFFECT] Sub-Menu when [M. SENSOR] on the [CAMERA SETUP] Sub-Menu is set to [ON], the Motion Sensor Function has priority and the selected digital effect is automatically cancelled. When [M. SENSOR] on the [CAMERA SETUP] Sub-Menu is set to [ON], it is not possible to manually start recording by pressing the Recording Start/Stop Button or to activate the Recording Check or Camera Search Function. When you use the AC Adaptor to power the Movie Camera, the Motion Sensor Function Stand-by Mode will continue when no movement is detected in the picture, even when the tape has reached the end during recording. When you use the Battery to power the Movie Camera, it remains in the Motion Sensor Function Stand-by Mode until the Battery is discharged, at which time the [CAMERA] Lamp flashes for a few seconds. To ensure correct functioning of the Motion Sensor Function, the moving subject should be quite large in the picture. Therefore, when you have zoomed the lens to the maximum wide-angle position, the distance between lens and subject should preferably be within about 2 metres. For subjects at larger distances, be sure to zoom in accordingly. The Movie Camera requires time to set up before recording starts. Therefore, the beginning of movement is not recorded. If there is a power interruption, the Motion Sensor Function is cancelled. !"# !"#$%&'()*+, -. /#0123#$%& !"#$%&'()*+, -. /0)1 x`^jbo^=pbqrmz !"xjKpbkploz !" !"xlkz !"#$%xafdfq^i bccb`qz !!"#$%&'()*+, -. / !"#$%&'()*+, -. /01234 x`^jbo^=pbqrmz !"xjKpbkploz xlkz !"#$%&'( L !"#$%&'( !"#$% &'( )*+, *-". [. . . ] (l 40) P4: The Date/Time/Title Indication is not displayed. S4-1: This is due to incorrect operation of the [DATE/TITLE] Button and/or the [MENU] Button. Press the [MENU] Button and set the desired Date/Time/Title Indication. Then press the [DATE/TITLE] Button so that the Date/Time/Title Indication appears. [. . . ]