User manual PANASONIC PT-40LC12

[. . . ] Multi-Media Projection Display Operating Instructions Models No. PT-40LC12/PT-45LC12 For assistance, please call : 1-888-VIEW PTV(843-9788) or send e-mail to : consumerproducts@panasonic. com or visit us at www. panasonic. com (USA) Three Important Reasons to Register Your Product Immediately! 1 Protect Your New Investment. . . Register your new projection display for insurance purposes in case your new projection display is stolen. Registering your product can help us to contact you in the unlikely event a safety notification is required under the Consumer Product Safety Act. Help us continue to design products that meet your needs. [. . . ] < Example > Press SAP CH 1 2 S T E R EO SAP MONO S T E R EO SAP MONO CH 1 2 CH 1 2 S T E R EO SAP MONO Press SAP Press SAP 35 Split screen Splitting the screen Press to split. (The previously selected screen appears on the left. ) +0! +0# Left screen (Main picture) · Returning to one screen. Right screen (Sub picture) Press to return. Selecting the screen mode for split screen. Press to select modes. +0! +0# SPLIT SCREEN FULL +0! Notes: · Sound from the Left screen is output from the speakers on the projection display set. · When the screen is split, signals of the Left screen are output from the rear monitor output terminal. · The left and right screens are processed by individual circuits and, therefore, may slightly vary in image quality. · Split screen returns to single screen when the projection display is turned off. · With the Left screen, as with a single screen, you can change the input, change channels, and adjust the volume. · The right and left screens cannot display the same picture at the same time. · A split screen which includes an RGB signal from a PC is fixed as SPLIT SCREEN NORMAL (PC input). +0# SPLIT SCREEN NORMAL 4/* +0# SPLIT SCREEN NORMAL (PC input) 36 For assistance, please call : 1-888-VIEW PTV(843-9788) Split screen Changing the channel of the right screen Swapping left and right screens Press to swap. 1 Press to select the desired channel. Example: During SPLIT SCREEN NORMAL. +0! +0# Example: During SPLIT SCREEN NORMAL. +0! +0# +0! +0$ +0# +0! Basic Operation PIP , buttons can also be used to select an outside input for the right side of the screen. Example: During SPLIT SCREEN NORMAL (PC input) CABLE TV 125 or 69 CH01 RGB * * * 4/* +0# CH125 * No input mode is displayed for terminals with no equipment connected. LINE 1 LINE 2 LINE 3 COMPONENT 2 * COMPONENT 1 * +0# 4/* Note: When outside input is finished, the lowest registered channel number is displayed. For faster selection, press the SWAP button to change the screen to the left. Then, press the TV/VIDEO button to directly change the input. Finally, press SWAP button again to change the screen back to the right. Note: Picture quality may change according to the combination of signals input to the left and right screens. 37 Picture in Picture (PIP) Screen You can view two pictures simultaneously using two tuners and picture in picture (PIP) display function. Display PIP screen Press to split (The previously selected screen appears on the Main. ) +0!212 +0# Main screen (Main picture) PIP screen (Sub picture) · Returning to one screen. Press to return. Notes: · Sound from the Main screen is output from the speakers on the projection display set. · In PIP mode, the Main screen signal is output from the rear monitor output terminal. · Because Main and PIP screens are processed by individual circuits, image quality may vary slightly. · PIP mode returns to single screen when the projection display is turned off. · The Main and PIP screens cannot display the same picture at the same time. · An RGB signal cannot be displayed on a PIP screen or a Main screen. · A component signal cannot be displayed on a PIP screen. Thus, when a component signal is displayed on the Main screen, the SWAP button becomes invalid. · With the Main screen, as with a single screen, you can change the input, change channels, and adjust the volume. 38 For assistance, please call : 1-888-VIEW PTV(843-9788) Picture in Picture (PIP) Screen Changing the channel of the PIP screen Press to select the desired channel. Example: During Main screen NORMAL. Swapping Main and PIP screens Press to swap. [. . . ] 9, 33 I ID-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Input 1 terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Input 2 terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Input 3 terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]