User manual PANASONIC PT-D4000U ADDITIONS

[. . . ] Operating Instructions DLPTM Based Projector Commercial Use Model No. PT-D4000U Read these instructions completely before operating this unit. TQBJ0222-3 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic DLPTM based projector. The serial number of your product may be found on its back. You should note it in the space provided below and retain this booklet in case service is required. Model number: PT-D4000U Serial number: IMPORTANT SAFETY NOTICE WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK. [. . . ] · Depending on the setting, some equipment may not provide images or otherwise operate properly. This lets you save the cursor position in on-screen menus. Note · Even when this is set to "ON", the cursor position is not saved if the main power of the projector is turned off. 33 OPTION2 settings OPTION2 PROJECTOR ID INSTALLATION ALTITUDE DIRECTION LAMP SELECT LAMP RELAY RS-232C SYSTEM INFORMATION AUTO POWER OFF DATE AND TIME PASSWORD ALL FRONT-FLOOR LOW HORIZONTAL DUAL OFF ALTITUDE The fan can be controlled in accordance with the operating conditions. HIGH : This is selected when using the projector at an altitude of over 1 400 m (4 593. 2'). DISABLE DIRECTION The fan can be controlled in accordance with the direction in which the images are to be projected. HORIZONTAL: This is the standard setting. VERTICAL : This is selected when projecting images at a significant angle toward the vertical (more than 30 degrees from the horizontal). MENU SELECT CHANGE PROJECTOR ID The projector has an ID number setting function that helps the user to control two or more projectors either simultaneously or separately with a single remote control. The ID number is set to "ALL" by default. Hence the ID number need not be set when only one projector is used. 1 ­ 64 : The ID number is set in this range. Note · The ID number can be set to "ALL", or selected from "1" to "64". · If the projectors are given ID numbers, their remote controls must be assigned the same ID numbers, respectively. · If the ID number of a projector is set to "ALL", it can be controlled by the remote control or the PC with any ID number. If multiple projectors are used and some of them have their IDs set to "ALL", they cannot be controlled separately from the projectors with other ID numbers. For details on remote control ID setting, see page 15. V H 30° 30° 30° 30° H V H: HORIZONTAL V: VERTICAL Attention · Select the correct "DIRECTION" setting in accordance with the direction in which the images are to be projected. Using the projector at the wrong "DIRECTION" setting will shorten the service life of the lamps. INSTALLATION Switch this setting according to the projector installation method. FRONT-FLOOR FRONT-CEILING REAR-FLOOR REAR-CEILING 34 LAMP SELECT "LAMP SELECT" is used to choose from "SINGLE" and "DUAL" modes depending on user's needs or viewing conditions. In "SINGLE" mode, the projector may automatically select either lamp from the 2 lamps, or the particular lamp can be specified. DUAL : Two lamps are used simultaneously. SINGLE : One of either lamps is used (lamp with shorter operating hours is automatically selected). When one of the above settings is selected, it will take effect after the ENTER button is pressed. Note · If, in the "SINGLE", "LAMP1" or "LAMP2" mode, one lamp remains off or the currently active lamp exceeds 3 000 hours of cumulative operating time, the other lamp will light. If, in the "DUAL" mode, one lamp remains off or the currently active lamp exceeds 3 000 hours of cumulative operating time, the other lamp alone will light. [. . . ] Contactez une entreprise d'évacuation des déchets industriels pour l'enlèvement des lampes usées. Si vous persistez à utiliser une lampe après le moment où elle aurait dû être remplacée, la lampe peut casser. Un tournevis Philips est requis pour le remplacement de la lampe. Faites attention que votre main ne glisse pas en utilisant le tournevis. [. . . ]