User manual PANASONIC PT-DW10000E BROCHURE

[. . . ] Operating Instructions DLP® Based Projector Commercial Use Models No. PT-D10000E PT-DW10000E Read these instructions completely before operating this unit. TQBJ 0209-6 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic DLP® based projector. The serial number of your product may be found on its back. You should note it in the space provided below and retain this booklet in case service is required. Model number: PT-D10000E/PT-DW10000E Serial number: 2 ­ ENGLISH Contents Be sure to read the "IMPORTANT SAFETY NOTICE" and the "Precautions with regard to safety". [. . . ] · THROUGH: Pictures are displayed without changing the resolution of the input signals. · 16:9*1: When standard signals are being input*3, pictures are displayed with the aspect ratio converted to 16:9. When wide-screen signals are being input*4, pictures are displayed with the aspect ration of the input signals unchanged. · 4:3*2: When standard signals are being input*3, pictures are displayed with the aspect ration of the input signals unchanged. When wide-screen signals are being input*4, the PT-D10000E displays the pictures with the aspect ratio converted to 4:3. The PT-DW10000E displays the pictures with the aspect ratio unchanged, but reduces the size of the pictures so that they fit within the 4:3 projection area. · Some size modes are not available for certain types of input signals. For NTSC signals, "DEFAULT" cannot be selected. · If an aspect ratio which is different from the aspect ratio for the input signals is selected, the pictures will appear differently from the originals. Be careful of this when selecting the aspect ratio. · If using this projector in places such as cafes or hotels to display programmes for a commercial purpose or for public presentation, note that adjusting the aspect ratio or using the zoom function to change the screen pictures may be an infringement of the rights of the original copyright owner for that programme under copyright protection laws. · If conventional (normal) 4:3 pictures which are not wide-screen pictures are displayed on a wide screen, the edges of the pictures may not be visible or they may become distorted. Such pictures should be viewed as with an aspect ratio of 4:3 in the original format intended by the creator of the pictures. ENGLISH ­ 57 Basic Operation MENU SELECT CHANGE *1 · S4:3 : Select when using a 16:9 screen. · H FIT*2: Pictures are displayed using all the panel pixels in the horizontal direction. Signals with an aspect ratio where the pictures are taller than with a ratio of 16:9 will be displayed with their bottom areas cut off. · HV FIT: Pictures are displayed on the whole panel pixels. If the aspect ratio of the input signals is different from that of the panel, the pictures are displayed by converting it into the panels aspect ratio (4:3 for PT-D10000E and 16:9 for PT-DW10000E). · VID AUTO: The projector identifies the video ID (VID) embedded in the picture signals and displays the picture by automatically switching the screen sizes between 4:3 and 16:9. This function is effective for the NTSC signal input. · S1 AUTO: The projector identifies the S1 signal and displays the picture by automatically switching the screen sizes between 4:3 and 16:9. This function is effective for S-Video NTSC signals. · VID AUTO (PRIORITY): The projector identifies the abovementioned VID or S1 signals and displays the picture by automatically choosing the screen sizes of 4:3 or 16:9 according to the VID if it is detected or S1 signals if a VID is not detected. [. . . ] · For the PT-DW10000E, the picture quality for the sub window will deteriorate if the size of the main window is 75 % or more and the size of the sub window is 50 % or more. ENGLISH ­ 119 Information Dimensions Outside dimensions unit : mm 320 OPEN FILTER CLEANING OFF AC IN ON MAIN POWER CLOSE 578 Installation dimensions diagram (Figure 1 : Dimensions applying when one unit is used) (Figure 2 : Dimensions applying when two units are used) Exhaust 50 cm or more 30 cm or more Exhaust 50 cm or more 50 cm or more 30 cm or more 50 cm or more Exhaust 10 cm or more 40 cm or more 40 cm or more Attention · Leave a clearance of at least 50 cm so that the ventilation opening on the rear panel will not be blocked. · Set up the projector so that air can flow freely around the rear of the projector without staying still. In addition, leave a space of 30 cm or more at the sides so that the hot air coming out from the air outlet vents does not get drawn in through the air intake vents. · Set up the projector with a space of 40 cm or more at the front so that the air filter can be replaced. [. . . ]