User manual PANASONIC PT-DW100U ADDITIONS

[. . . ] Operating Instructions 3-chip DLP®-based Projector Commercial Use Models No. PT-DW100U Read these instructions completely before operating this unit. TQBJ 0267-3 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic ® DLP based projector. The serial number of your product may be found on an attached label. You should note it in the space provided below and retain this booklet in case service is required. [. . . ] Press to switch "AUTO SIGNAL". · The setting will change as follows each time is pressed. OFF ON Large Screen Correction When viewing images close up on a large screen, you can correct the colors that appear lighter on the screen so that they appear the same as the colors that would appear on a normal-sized screen. · If unregistered signals are input when "ON" is selected, auto setup will be initiated automatically. AUTO SETUP 5. Press to select "AUTO SETUP". Press ENTER. · The "AUTO SETUP" screen will be displayed. AUTO SETUP MODE DEFAULT 1. Press to select "LARGE SCREEN CORRECTION". COLOR MATCHING LARGE SCREEN CORRECTION RGB IN OFF OFF 2. Press to switch "LARGE SCREEN CORRECTION". · The setting will change as follows each time is pressed. OFF (No correction) 2 (High) 1 (Low) 7. Press to switch "MODE". · The setting will change as follows each time is pressed. DEFAULT WIDE USER 70 ­ ENGLISH · DEFAULT: To receive signals of which image aspect is 4:3 or 5:4 (applicable resolution : 640 × 400, 640 × 480, 800 × 600, 832 × 624, 960 × 720, 1 024 × 768, 1 152 × 864, 1 152 × 870, 1 280 × 960, 1 280 × 1 024, 1 600 × 1 200, 1 400 × 1 050) · WIDE: To receive signals of which the image aspect is wide (applicable resolution: 720 x 400, 848 x 480, 1 280 x 720, 1 024 x 600, 1 120 x 750, 1 440 x 900, 1 680 x 1 050) · USER: To receive signals of specific horizontal resolution (number of horizontally displayed dots) · EDID1 (Input signal formats supported) : Mainly select this when an external device (DVD player, etc. ) for outputting video signals of a moving image system is connected to DVI-D IN. · EDID2 (Input signal formats supported) : Mainly use this when an external device (PC, etc. ) for outputting video signals of a still image system is connected to DVI-D IN. 4. Press to switch "DVI SIGNAL LEVEL". · The setting will change as follows each time is pressed. 0-255:PC 16-235 8. If "User" is selected, press to enter the horizontal resolution of signal source into "DISPLAY DOTS". Press ENTER. · Execute automatic adjustment. A message "PROGRESS. . . " appears during automatic adjustment. When the adjustment is complete, the system returns to the input screen. · 0-255:PC: Select this when, for example, an external device (PC, etc. ) is connected via the DVI terminal output. · 16-235: Select this when, for example, an external device (DVD player, etc. ) is connected via the HDMI terminal output using a conversion cable. Note · The optimal setting differs depending on the output setting of the connected external device. Refer to the instruction manual of the external device. · If the setting is changed, the data for plug and play changes. For the plug and play compatible resolutions, check the compatible signal list (pp. 120-121). DVI-D IN Change this setting if video does not display normally when the projector and an external device are connected via DVI-D. 1. Press to select "DVI-D IN". RGB IN DVI-D IN AUX DVI IN 2. Press ENTER. · The "DVI-D IN" screen will be displayed. DVI-D IN DVI EDID DVI SIGNAL LEVEL EDID1 0-255:PC 3. Press to switch "DVI EDID". · The setting will change as follows each time is pressed. EDID1 EDID2(PC) ENGLISH ­ 71 Special Features Display Option settings (continued) AUX DVI IN (Only when the ET-MD77DV is installed) Change this setting if video does not display normally when the ET-MD77DV and an external device are connected via DVI-D. AUX SDI IN Set this in accordance with the input module (sold separately). 1. Press to select "AUX DVI IN". DVI-D IN AUX DVI IN AUX SDI IN 1. Press to select "AUX SDI IN". AUX DVI IN AUX SDI IN ON-SCREEN DISPLAY 2. [. . . ] Consulter votre revendeur pour plus de détails à propos des commandes. N de modèle de l'unité de remplacement de la lampe : ET-LAD12K (ampoule simple), ET-LAD12KF (4 ampoules) Puissance : 300 W · Des lampes autres que celles spécifiées ci-dessus ne devront en aucun cas être utilisées. N'utiliser que les types de lampe spécifiés. Intervalle de remplacement de la lampe Toute lampe utilisée en tant que source de lumière a une durée de vie limitée. La durée de vie de la lampe utilisée dans ce projecteur est de 2 000 heures. [. . . ]