User manual PANASONIC PT-DW530E

[. . . ] Operating Instructions DLPTM Based Projector Model No. Functional Manual Commercial Use PT-DZ570E PT-DW530E PT-DX500E Thank you for purchasing a Panasonic Projector. J Before operating this product, please read the instructions carefully and save this manual for future use. J Before using your projector, be sure to read "Precautions with regard to safety" (Æ pages 9 to 17). M1010TK0 -DW TQBJ0350 ENGLISH Important Safety Important Safety Notice Notice Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic DLPTM Based projector. The serial number of your product may be found on its bottom. [. . . ] 6 ) Press <DEFAULT> button on the remote control to restore the factory default. 7 ) Follow the same procedure (steps 5-6) to restore the factory default for [TINT], [COLOR TEMPERATURE] and [GAMMA]. z sRGB is only enable when RGB signals are being input. Select from RGB and YCBCR. z Other signals Select from RGB and YPBPR. z Refer to "List of compatible signals" (Æpage 88) for available signals. z Malfunction may occur or other problems could be encountered with some equipment. Note Note ENGLISH - 47 Settings POSITION menu z See "Navigating through the menu" (Æpage 40). z See "MAIN MENU" and "SUB MENU" (Æpage 41). ASPECT This changes the aspect ratio of the projected image. This changes the aspect ratio for the screen range selected with [SCREEN SETTING]. (Æpage 55) 1 ) Press to select [ASPECT]. 2 ) Press or <ENTER> button. be displayed. z The [ASPECT] individual adjustment screen will SHIFT This function allows the user to adjust the raster position vertically or horizontally if the position of the image projected on the screen is displaced even when the projector is properly aligned with the screen, and the internal test patterns are correctly framed. 3 ) Press to switch [ASPECT]. is pressed. z The setting will change as follows each time VID AUTO *1 DEFAULT AUTO *2 THROUGH HV FIT 16 : 9 V FIT H FIT 4:3 S1 AUTO *3 VID AUTO (PRI. ) *3 1 ) Press to select [SHIFT]. 2 ) Press <ENTER> button. z The [SHIFT] screen will be displayed. 3 ) Press to adjust the position. J For vertical (up and down) adjustment Operation Press . The picture position moves up. Adjustment *1 : VIDEO/S-VIDEO (NTSC) only *2 : RGB1/RGB2 (480i, 480p) only *3 : S-VIDEO (NTSC) only J DEFAULT Pictures are displayed without changing the aspect ratio of the input signals. J VID AUTO The projector identifies the video ID (VID) embedded in the picture signals and displays the picture by automatically switching the screen sizes between 4 : 3 and 16 : 9. This function is effective for the NTSC signal input. Press . The picture position moves down. Settings J For horizontal (right and left) adjustment J AUTO The projector identifies the video ID (VID) embedded in the picture signals and displays the picture by automatically switching the screen sizes between 4 : 3 and 16 : 9. This function is effective for the 480i/480p signal input. Operation Press . Adjustment The picture position moves to the right. The picture position moves to the left. J S1 AUTO The projector identifies the S1 signal and displays the picture by automatically switching the screen sizes between 4 : 3 and 16 : 9. This function is effective for S-VIDEO NTSC signals. Press . 48 - ENGLISH POSITION menu J VID AUTO (PRI. ) The projector identifies the abovementioned VID or S1 signals and displays the picture by automatically choosing the screen sizes of 4 : 3 or 16 : 9 according to the VID if it is detected or S1 signals if a VID is not detected. This function is effective for S-Video NTSC signals. z Some size modes are not available for certain types of input signals. For NTSC signals, [DEFAULT] cannot be selected. z If an aspect ratio which is different from the aspect ratio for the input signals is selected, the pictures will appear differently from the originals. Be careful of this when selecting the aspect ratio. z If using this projector in places such as cafes or hotels to display programs for a commercial purpose or for public presentation, note that adjusting the aspect ratio or using the zoom function to change the screen pictures may be an infringement of the rights of the original copyright owner for that program under copyright protection laws. z If conventional (normal) 4 : 3 pictures which are not wide-screen pictures are displayed on a wide screen, the edges of the pictures may not be visible or they may become distorted. Such pictures should be viewed as with an aspect ratio of 4 : 3 in the original format intended by the creator of the pictures. Note J THROUGH Pictures are displayed without changing the resolution of the input signals. J 16 : 9 When standard signals *4 are input, the pictures are displayed with the aspect ratio converted to 16 : 9. When wide signals are input *5, the pictures are displayed without changing the aspect ratio. J4 : 3 When standard signals *4 are input, the pictures are displayed without changing the aspect ratio. [. . . ] registered in the United States and other countries. z PJLinkTM is a pending trademark in Japan, the United States, and other countries and regions. z HDMI, the HDMI logo and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing LLC. z Other types of names such as company names and product names appearing in this instruction manual are trademarks or registered trademarks of their respective holders. [. . . ]