User manual PANASONIC PT-DW6300E ADDITIONS

[. . . ] Operating Instructions DLPTMBased Projector Commercial Use Model No. PT-DZ6710E PT-DZ6700E PT-DW6300E PT-D6000E PT-D5000E STANDBY(RED)/ ON(GREEN) LAMP TEMP FILTER Before operating this product, please read the instructions carefully and save this manual for future use. The information of these instructions are shared use with multiple models of DZ6710 series, DZ6700 series, DW6300 series, D6000 series and D5000 series. TQBJ0296-5 ENGLISH Important Safety Notice Important Information Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic DLPTMBased projector. The serial number of your product may be found on its bottom. [. . . ] Switch off the power to the projector when not in use. If the projector is switched on again while the internal cooling fan is still operating by the internal power supply, it may take a while to start the projection. ENGLISH - 18 Projecting Projecting a image Switching on the projector When using an optional lens, install a projection lens before switch on the projector. Connect the supplied mains lead (220 - 240 V AC, 50 Hz/60 Hz) to the AC IN terminal. Remove the projection lens cover from the lens. Switch the POWER switch on that is on the side of the projector. The power indicator lamp on the projector will flash in red. After a short period, the indicator will illuminate and the projector will enter standby mode. Making adjustment and selection It is recommended that the projector be allowed to warm up for at least 30 minutes before any adjustments are made to the focus. Select and set the projection scheme of INSTALLATION and COOLING CONDITION settings in PROJECTOR SETUP menu. Select the input signal by pressing the INPUT SELECT buttons. Adjust the vertical tilt of the projector with the front leg adjusters. Adjust the shift position of the projection. If the input signal is RGB signal, additionally press the AUTO SETUP button to adjust the position of the image. 6. Zoom the lens so the image fills the screen. Readjust the zoom so that the image size fits in the screen. Press the POWER ON button The power indicator lamp illuminates in green and soon the image is projected on the screen. AC IN terminal Adjusting focus, zoom and shift Pressing the LENS button changes the setup screen in order of FOCUS, ZOOM and SHIFT. Press FOCUS, ZOOM or SHIFT button Remote control buttons to display the setup screen. Control buttons of the projector POWER ON button . NOTE: · If the projector is powered up at about 0 °C (32 °F), a warmup period of approximately 5 minutes may be necessary to start projection. The temperature monitor (TEMP) lamp lights up during the warm-up period. When the warm-up is completed, the temperature monitor (TEMP) lamp turns off and the image is projected on the screen. · If the temperature of the operating environment is low and warm-up takes more than 5 minutes, the projector will judge that a problem has occurred and the power will be turned off automatically. If this happens, increase the temperature around the projector so that it is 0 °C (32 °F) or higher, and then turn on the POWER switch and press the POWER ON button again. LENS button CAUTION: · Be careful not to catch your fingers between the lens and shroud when shifting the lens. NOTE: · The setup screen will be displayed with the optional fixed lens though, it will not be functioning. · Pressing F G I or H for 3 seconds or more, performance the adjustment faster. ENGLISH - 19 Basic Operation INPUT SELECT buttons Projecting Switching off the projector 1. Press the POWER STANDBY button. The confirmation screen will be displayed. Lens home position 1. Press and hold the LENS button of the control button on the projector or SHIFT button of the remote control for 3 seconds or more. The HOME POSITION setup screen will be displayed for 5 seconds. POWER STANDBY button 2. [. . . ] 13 SERIAL Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 SHIFT Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Adjustment range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Remote control button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]