User manual PANASONIC PT-DW6300U ADDITIONS

[. . . ] Operating Instructions DLPTMBased Projector Commercial Use Model No. PT-DZ6710U PT-DZ6700U PT-DW6300U PT-D6000U PT-D5000U STANDBY(RED)/ ON(GREEN) LAMP TEMP FILTER Before operating this product, please read the instructions carefully and save this manual for future use. The information of these instructions are shared use with multiple models of DZ6710 series, DZ6700 series, DW6300 series, D6000 series and D5000 series. TQBJ0295-4 ENGLISH Important Safety Notice Important Information Dear Panasonic Customer: The following information should be read and understood as it provides details, which will enable you to operate the projector in a manner which is both safe to you and your environment, and conforms to legal requirements regarding the use of projectors. Before connecting, operating or adjusting this projector, please read these instructions completely and save this booklet with the projector for future reference. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic DLPTMBased Projector. [. . . ] Automatically the projector will be powered off after 10 minutes. NOTE: · The guide times, 1 800*2 and 2 000*1 hours, are rough estimates based on certain conditions and are not a guaranteed time. · For more information about the lamp unit, see the instructions which is provided with the lamp unit. 2 800 hours for PT-D5000U. Maintenance ENGLISH - 30 Replacement Replacement procedure Removing and replacing the lamp unit 1. Use a Phillips-head screwdriver to loosen the "lamp unit cover fixing screw" (1 screw) on the back of the projector until the screws turn freely, and remove the lamp unit cover. Slide the lamp unit cover to the control buttons and pull to remove. 4. Hold the handle of the new lamp unit and replace it in correct direction. Press in the lamp unit until it clicks and make sure the unit is installed securely. Tighten the "lamp unit fixing screws" (3 screws) securely with a Phillips-head screwdriver. Lamp unit cover fixing screw Fan electric power connector Lamp unit cover 2. Use a Phillips-head screwdriver to remove the "lamp unit fixing screws" (3 screws). Hold the handles of the lamp unit and pull the used lamp unit gently from the projector. Lamp unit fixing screws Handle 7. Attach the lamp unit cover and tighten the "lamp unit cover fixing screw" (1 screw) securely with a Phillips-head screwdriver. Slide the lamp unit cover to the hinge side along the guide and push in to attach securely. Make sure the fan electric power connector of the lamp unit cover is inserted securely to the projector's connector. Handle Lamp unit fixing screws NOTE: ENGLISH - 31 Maintenance · The lamp unit and the lamp unit cover must be attached correctly and securely. Failure to do so, the projector will bot be turned on for the protection circuit. · When the lamp unit is replaced, the duration of usage time will be reset to "0". Replacement Replacing the Auto Cleaning Filter (ACF) Before replacing the ACF Wait until the cooling fan stops and turn off the POWER switch of the projector in proper way. Disconnect the power cord from the wall outlet. Contact an Authorized Service Center to purchase a replacement ACF (ET-ACF100). The ACF unit to be replaced should be an unused product. When to replace the ACF The ACF unit is consumable product and effects on ventilation. The FILTER indicator will inform you of the replacement timing. You can check the remaining amount of the ACF unit in REMAINING FILTER of STATUS in PROJECTOR SETUP menu. Replacement procedure 1. Loosen "ACF cover fixing screw" (1 screw) until the screws turn freely and remove the ACF cover. Resetting the REMAINING FILTER 1. Turn on the projector and display the FILTER COUNTER RESET in PROJECTOR SETUP menu. Press the ENTER button. The confirmation screen will be displayed. 3. Select OK by pressing I, then press the ENTER button. [. . . ] Utilisez un tournevis cruciforme pour retirer les 3 vis de fixation de la lampe. Tenez les poignées de la lampe et tirez doucement la lampe usagée hors du projecteur. Vis de la lampe Poignée 7. Montez le couvercle de la lampe et serrez fermement la vis de fixation du couvercle de la lampe à l'aide d'un tournevis cruciforme. Faites glisser le couvercle de la lampe du côté de la charnière et poussez-le pour le monter fermement. Vérifiez que le connecteur d'alimentation électrique du ventilateur est bien introduit sur le connecteur du projecteur. Poignée Vis de la lampe 4. [. . . ]