User manual PANASONIC PT-DW7000

[. . . ] Operating Instructions DLPTM Based Projector Commercial Use Model No. PT-D7700U PT-DW7000U ON POWER OFF AUTO SETUP RGB 1 RGB 2 AUX SHUTTER VIDEO S-VIDEO SHUT MENU FREEZE PAGE UP ENTER PAGE DOWN ON SCREEN 1 4 7 STD FUNC 2 5 OSD 3 6 SYSTEM SEL D. ZOOM 1 BRIGHT CONTRAST LENS 8 ASPECT 9 0 USER NEXT LIGHT ID ALL ID SET LASER ON/OFF Computer Numetric Projector Read these instructions completely before operating this unit. TQBJ 0146-1 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic DLPTM based projector. The serial number of your product may be found on its back. You should note it in the space provided below and retain this booklet in case service is required. Model number: PT-D7700U / PT-DW7000U Serial number: IMPORTANT SAFETY NOTICE WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK. [. . . ] · SMPTE is the factory default. 61 How to use ADVANCED MENU Blanking adjustment Blanking adjustment fine-tunes the images projected by the video deck or other devices when the noise appears on the edges of the screen or if a part of the image lies slightly offscreen. Procedure of adjustment MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN SIGNAL LIST SECURITY Press the "MENU" button. The MAIN MENU screen will be displayed. Select the "ADVANCED MENU" with the buttons. :MENU SELECT ENTER:SUB MENU ADVANCED MENU DIGITAL CINEMA REALITY FORMAT BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING SYNC. TERM RASTER POSITION Press the "ENTER" button. AUTO SMPTE The ADVANCED MENU screen will be displayed. Select "BLANKING" with the buttons. OFF 75 :MENU SELECT ENTER:SUB MENU BLANKING UPPER LOWER LEFT RIGHT Press the "ENTER" button. 0 0 0 0 The BLANKING adjustment screen will be displayed. Select the desired item for adjustment with the buttons. Adjust blanking with the buttons. The value changes from 0 to 511. :MENU SELECT :ADJUST <When correcting the upper blanking of the screen (top) > Press button to move the blanking zone upward; button to downward. <When correcting the lower blanking of the screen (bottom) > Press button to move the blanking zone upward; button to downward. <When correcting the left hand blanking of the screen (left) > Press button to move the blanking zone to the right; button to the left. <When correcting the right hand blanking of the screen (right) > Press button to move the blanking zone to the right; button to the left. 62 Adjusting the input resolution Input resolution adjustment achieves the best image when the screen flickers or halo is observed around the contour. Procedure of adjustment MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN SIGNAL LIST SECURITY Press the "MENU" button. The MAIN MENU screen will be displayed. Select the "ADVANCED MENU" with the buttons. :MENU SELECT ENTER:SUB MENU ADVANCED MENU DIGITAL CINEMA REALITY FORMAT BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING SYNC. TERM RASTER POSITION Press the "ENTER" button. AUTO SMPTE The ADVANCED MENU screen will be displayed. Select "INPUT RESOLUTION" with the buttons. OFF 75 :MENU SELECT ENTER:SUB MENU INPUT RESOLUTION TOTAL DOTS DISPLAY DOTS TOTAL LINES DISPLAY LINES Press the "ENTER" button. 1056 832 666 624 The INPUT RESOLUTION screen will be displayed. Select one of the following items with the buttons and adjust it with the buttons. "TOTAL DOTS", "DISPLAY DOTS", "TOTAL LINES" and "DISPLAY LINES" Each item automatically displays a value in response to the type of the input signal. If vertical stripes appear on the screen or the image is partly missing, increase or decrease the displayed value while observing the screen to achieve the optimal value. :MENU SELECT :ADJUST Note · The abovementioned vertical stripes will not appear on the screen when all signals are input. · The picture may be distorted during the adjusting operation, but this is not a fault. · The input resolution can be adjusted only when RGB signal input is applied with RGB1, RGB2 IN, and the analog RGB input module (optional: ET-MD95RGB). 63 How to use ADVANCED MENU Adjusting the clamp position Use the clamp position adjustment to achieve the optimal value when dark areas of the image are crushed or displayed in green. Procedure of adjustment MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN SIGNAL LIST SECURITY Press the "MENU" button. The MAIN MENU screen will be displayed. Select "ADVANCED MENU" with the buttons. :MENU SELECT ENTER:SUB MENU ADVANCED MENU DIGITAL CINEMA REALITY FORMAT BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING SYNC. TERM RASTER POSITION Press the "ENTER" button. AUTO SMPTE The ADVANCED MENU screen will be displayed. Select "CLAMP POSITION" with the buttons. OFF 75 :MENU SELECT ENTER:SUB MENU CLAMP POSITION POSITION Press the "ENTER" button. 1 The CLAMP POSITION screen will be displayed. Adjust with the buttons. The value changes from 1 to 255. :MENU SELECT :ADJUST The optimal value for the clamp position adjustment · If dark areas are crushed: The optimal value is the point where the dark area is best improved. · If the dark areas are displayed in green: The optimal value is the point where the green area becomes dark and clear. Note · The clamp position can be adjusted only when the RGB signal input is applied with RGB1, RGB2 IN, and the analog RGB input module (optional: ET-MD95RGB). 64 Edge blending adjustment This projector has the function to hide the seams for multi-screens. Procedure of adjustment MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN SIGNAL LIST SECURITY Press the "MENU" button. The MAIN MENU screen will be displayed. Select the "ADVANCED MENU" with the buttons. ADVANCED MENU DIGITAL CINEMA REALITY FORMAT BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING SYNC. TERM RASTER POSITION Press the "ENTER" button. AUTO SMPTE The ADVANCED MENU screen will be displayed. ON 75 Select "EDGE BLENDING" with the buttons. Select "OFF", "ON" or "USER" with the buttons. OFF: When the multi-screens are not going to be used. ON: When the tilting inside the unit is to be used for the tilting of the edge blending area. USER: When a specific tilting is to be used for the tilting of the edge blending area. (Separate software is required to establish these settings. Consult your dealer. ) :MENU SELECT :CHANGE ENTER:SUB MENU EDGE BLENDING UPPER OFF LOWER OFF LEFT OFF RIGHT OFF MARKER BRIGHT ADJUST Press the "ENTER" button. START WIDTH START WIDTH START WIDTH START WIDTH 0 128 0 128 0 128 0 128 OFF The EDGE BLENDING screen will be displayed. Specify the area to be adjusted with the buttons. To joint the top: set "UPPER" to "ON". To joint the bottom: set "LOWER" to "ON". To joint the left: set "LEFT" to "ON". To joint the right: set "RIGHT" to "ON". :MENU SELECT :ADJUST ENTER:CHANGE Press the "ENTER" button to toggle "ON" and "OFF". Adjust the compensation width and start position with the buttons. <To display the adjustment marker> The optimal point is where these lines overlap. Select "MARKER" with the buttons. Select "ON" with the ENTER buttons. (Continued on next page) Note Adjustment marker When the "MARKER" is set to "ON", the image position adjustment marker is displayed. The optimal point is the position where the red line of one frame overlaps the green line of the other frame. Notice: The correction widths of the jointed frames must be the same value all the time. The optimal joint cannot be achieved if the jointed frames have different correction widths. Red line Green line Green line Red line 65 How to use ADVANCED MENU Edge blending adjustment (continuing) BRIGHT ADJUST BRIGHT INSIDE BRIGHT OUTSIDE UPPER LOWER LEFT RIGHT 6 6 0 0 0 0 Select the "BRIGHT ADJUST" with the buttons. Press the ENTER button. The BRIGHT ADJUST screen will be displayed. Projection range Edge blending width (right) BRIGHT adjustment (right) Marker Select the "BRIGHT INSIDE" with the buttons. Adjust the compensation value (0-255) with the buttons. [. . . ] Mettez hors tension en suivant la procédure de la page 39 à 40, débranchez la fiche électrique et vérifiez que les éléments autour de la lampe ont refroidi. En utilisant un tournevis Phillips, retirez les 7 vis de la porte d'accès à la lampe située à l'arrière du projecteur. Retirez la porte du logement de lampe du projecteur. Attention · Faites attention de ne pas casser le cliquet situé au centre de la partie inférieure de la porte dÅfaccès la lampe. Vis de fixation Cache de la lampe 4. [. . . ]