User manual PANASONIC PT-DZ110XE

[. . . ] Operating Instructions DLPTM Based Projector Model No. Functional Manual Commercial Use PT-DZ110XE PT-DS100XE PT-DW90XE The projection lens is sold separately. Thank you for purchasing a Panasonic Projector. J Before operating this product, please read the instructions carefully and save this manual for future use. J Before using your projector, be sure to read "Precautions with regard to safety" (Æ pages 9 to 17). TQBJ0342 ENGLISH Important Safety Important Safety Notice Notice Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic DLPTM Based projector. The serial number of your product may be found on its bottom. [. . . ] 2 ) Press or <ENTER> button. z The [DIGITAL CINEMA REALITY] individual adjustment screen will be displayed. be changed within a range of 0 to 599 vertically and 0 to 959 horizontally. z The adjustment value for the PT-DS100XE can be changed within a range of 0 to 524 vertically and 0 to 699 horizontally. z The adjustment value for the PT-DW90XE can be changed within a range of 0 to 383 vertically and 0 to 682 horizontally. When correcting the upper blanking of the screen (top) Press to move the blanking zone upward; Press to downward. When correcting the lower blanking of the screen (bottom) Press to move the blanking zone upward; Press to downward. When correcting the left hand blanking of the screen (left) Press to move the blanking zone to the right; Press to the left. When correcting the right hand blanking of the screen (right) Press to move the blanking zone to the right; Press to the left. 3 ) Press to select [DIGITAL CINEMA REALITY]. z The setting will change as follows each time is pressed. AUTO OFF 25p FIXED : When 576i or 1 080/50i signals are input 30p FIXED : When 480i or 1 080/60i signals are input AUTO Performs automatic detection and cinema processing. (factory default) Unforced cinema processing. Forced cinema processing (2 : 2 pulldown) is performed when a 576i or 1 080/50i signal is input. Forced cinema processing (2 : 2 pulldown) is performed when a 480i or 1 080/60i signal is input. Settings OFF 25p FIXED 30p FIXED Note z In [DIGITAL CINEMA REALITY] mode, the image quality will be deteriorated if [30p FIXED] or [25p FIXED] is selected when the signal is not a 2 : 2 pulldown signal. 64 - ENGLISH ADVANCED MENU INPUT RESOLUTION Input resolution adjustment achieves the best image when the screen flickers or halo is observed around the contour. Set the values appropriately for the signal resolution that is being used. EDGE BLENDING The built-in edge blending feature allows multiple projector images to be seamlessly overlapped. 1 ) Press to select [INPUT RESOLUTION]. 2 ) Press <ENTER> button. displayed. 1 ) Press to select [EDGE BLENDING]. 2 ) Press to switch [EDGE BLENDING]. is pressed. z The [INPUT RESOLUTION] screen will be z The setting will change as follows each time 3 ) Press to select [TOTAL DOTS], [DISPLAY DOTS], [TOTAL LINES] or [DISPLAY LINES], and the press to adjust it. z Each item automatically displays a value in OFF ON USER OFF ON When the multi-screens are not going to be used. When the default linear blending ramps are sufficient. When a user-defined blending ramp is required. These ramps can be defined and uploaded to the projector through the RS-232 port. Consult your dealer for details. response to the type of the input signal. If vertical stripes appear on the screen or the image is partly missing, increase or decrease the displayed value while observing the screen to achieve the optimal value. USER z The vertical stripes will not appear on the all white signal image. z The picture may be distorted during the adjusting operation, but this is not a fault. z The [INPUT RESOLUTION] can be adjusted only when RGB signal input is applied with RGB1 and RGB2 IN. Note 3 ) Press <ENTER> button. displayed. z The [EDGE BLENDING] screen will be CLAMP POSITION Use the clamp position adjustment to achieve the optimal value when dark areas of the image are crushed or displayed in green. 4 ) Press to specify the area to be adjusted. [ON]. z To blend the top edge: set [UPPER] to [ON]. z To blend the bottom edge: set [LOWER] to z To blend the left edge: set [LEFT] to [ON]. [. . . ] z Other types of names such as company names and product names appearing in this instruction manual are trademarks or registered trademarks of their respective holders. The ® and TM marks are not indicated in this instruction manual. ENGLISH - 127 Appendix Ceiling mount bracket safeguards When installing the ceiling mount bracket to the projector, install the accessory Drop-prevention bracket (Safety cables) to the projector. (The projector will still be safe if they are not used, however they will help prevent the possibility of accidents caused by the projector falling down if the screws happen to become loose. ) Ceiling bracket : For high ceiling : ET-PKD310H, For low ceiling : ET-PKD310S, Ceiling Mount Attachment : ET-PAD310 Installation work of the ceiling mount bracket should only be carried by a qualified technician according to the following procedure. z Panasonic takes no responsibility for any losses or damage occurring as a result of using a ceiling mount z z z z z z z bracket not manufactured by Panasonic, or if damage to the projector occurs as a result of an inappropriate location used for installing the ceiling mount bracket, even if the projector's warranty period has not yet expired. Use a torque screwdriver or similar tool to tighten the screws. [. . . ]