User manual PANASONIC PT-DZ12000U ADDITIONS

[. . . ] Operating Instructions 3-chip DLP®-based Projector Commercial Use Models No. PT-D12000U PT-DZ12000U Read these instructions completely before operating this unit. TQBJ 0263-4 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic ® DLP based projector. The serial number of your product may be found on an attached label. You should note it in the space provided below and retain this booklet in case service is required. [. . . ] The effects can be confirmed on the colorimeter. After all the data has been input, press MENU. Note · If "709MODE" has been selected as the "COLOR MATCHING" setting, the 3 primary colors defined by the ITU-R BT. 709 standard will be set as the target data. · If the target data is outside the color range of the projector, the colors will not be projected correctly. 2. Press ENTER. · The "SCREEN SETTING" screen will be displayed. SCREEN SETTING SCREEN FORMAT SCREEN POSITION 16:9 0 3. Press to switch "SCREEN FORMAT". · The setting will change as follows each time is pressed. PT-DZ12000U 16:10 16:9 PT-D12000U 4:3 16:9 Large Screen Correction When viewing images close up on a large screen, you can correct the colors that appear lighter on the screen so that they appear the same as the colors that would appear on a normal-sized screen. 4. Press to adjust "SCREEN POSITION". · In the case of the PT-DZ12000U, you can adjust the setting from -60 to +60. This allows a 16:9 image to be moved up and down within the 16:10 screen. · In the case of the PT-D12000U, you can adjust the setting from -132 to +131. 1. Press to select "LARGE SCREEN CORRECTION". COLOR MATCHING LARGE SCREEN CORRECTION SCREEN SETTING OFF OFF Note · "SCREEN POSITION" cannot be adjusted when "SCREEN FORMAT" is "16:10" (PT-DZ12000U) and "4:3" (PT-D12000U). 2. Press to switch "LARGE SCREEN CORRECTION". · The setting will change as follows each time is pressed. OFF (No correction) 2 (High) 1 (Low) RGB IN (Only RGB input) When unregistered signals are to be input frequently because the unit is used at conferences or other venues, the screen display position can be adjusted automatically without having to press AUTO SETUP on the remote control each time. Use this setting when adjusting a specific or oblong (16:9, etc. ) signal. Screen setting Set this in accordance with the screen you are using. When the projection image aspect ratio is changed, the projector makes corrections to ensure the optimal images for the set screen size. 1. Press to select "RGB IN". SCREEN SETTING RGB IN DVI-D IN 1. Press to select "SCREEN SETTING". LARGE SCREEN CORRECTION SCREEN SETTING RGB IN OFF 2. Press ENTER. · The "RGB IN" screen will be displayed. RGB IN AUTO SIGNAL AUTO SETUP OFF AUTO SIGNAL 3. Press to select "AUTO SIGNAL". 72 ­ ENGLISH 4. Press to switch "AUTO SIGNAL". · The setting will change as follows each time is pressed. OFF ON DVI-D IN Change this setting if video does not display normally when the projector and an external device are connected via DVI-D. 1. Press to select "DVI-D IN". RGB IN DVI-D IN AUX DVI IN · If unregistered signals are input when "ON" is selected, auto setup will be initiated automatically. 2. Press ENTER. · The "DVI-D IN" screen will be displayed. DVI-D IN DVI EDID DVI SIGNAL LEVEL EDID1 0-255:PC AUTO SETUP 5. Press to select "AUTO SETUP". Press ENTER. · The "AUTO SETUP" screen will be displayed. AUTO SETUP MODE DEFAULT 3. Press to switch "DVI EDID". · The setting will change as follows each time is pressed. EDID1 EDID2(PC) 7. [. . . ] Consulter votre revendeur pour plus de détails à propos des commandes. N de modèle de l'unité de remplacement de la lampe : ET-LAD12K (ampoule simple), ET-LAD12KF (4 ampoules) Puissance : 300 W · Des lampes autres que celles spécifiées ci-dessus ne devront en aucun cas être utilisées. N'utiliser que les types de lampe spécifiés. Intervalle de remplacement de la lampe Toute lampe utilisée en tant que source de lumière a une durée de vie limitée. La durée de vie de la lampe utilisée dans ce projecteur est de 2 000 heures. [. . . ]