User manual PANASONIC PT-F100

[. . . ] Operating Instructions LCD Projector Commercial Use Model No. PT-F100NTU PT-F100U Before operating this product, please read the instructions carefully and save this manual for future use. TQBJ0213 ENGLISH Important Safety Notice Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector. The serial number of your product may be found on its bottom. [. . . ] Select OK and press ENTER to set the entered text in a box. Press G and edit the TEXT2 if you need to, and repeat the step 3 - 5. Settings COMPUTER2 SELECT You can switch the function of the COMPUTER2 IN/ 1 OUT terminal. INPUT OUTPUT COMPUTER2 IN COMPUTER1 OUT LAMP RUNTIME You can check how long the lamp has been used. NOTE: · LAMP RUNTIME is a relevant matter for lamp replacement timing. See "Replacing the Lamp unit" on page 43. · When the lamp unit is replaced with the new one (ET-LAF100), the setting will be reset to "0". ENGLISH - 36 OPTION menu FILTER REMAINING You can check the remaining amount of the ARF (Auto Rolling Filter). The color of the bar scale is indicating the condition of the ARF. Yellow Red The filter remaining amount is getting low. No more remaining. CONTROL PANEL You can turn off the function of the control panel buttons on the projector body. Press I H to select the required option. INVALID Invalidate the control panel buttons Confirmation screen will be displayed. Validate the control panel buttons VALID NOTE: · See "Replacing the ARF (Auto Rolling Filter)" on page 42. · After you replace the ARF, FILTER REMAINING should be reset to "0" by pressing the ENTER button for 3 seconds. AUTO SETUP You can turn off the AUTO SETUP function for when the COMPUTER signal is detected. AUTO When the projector detect a COMPUTER signal, adjust the projected image position automatically for SIGNAL SEARCH, DOT CLOCK and CLOCK PHASE. Only when the AUTO SETUP button is pressed, the projected image position will be adjusted for DOT CLOCK and CLOCK PHASE. See "Remote control" on page 13. POWER OFF TIMER You can set the off timer to switch off the POWER of the projector after a certain period of time automatically when no signal is detected. Press I H to select the required period from 15 to 60 minutes at intervals of 5 minutes. BUTTON DISABLE 15 MIN. 40 MIN. NOTE: · Usually the recommended setting is AUTO. SIGNAL SEARCH You can turn off the auto signal detecting system. ON OFF Detect the input signal from the terminals and project the image. Deactive NOTE: · SIGNAL SEARCH is not available when any input signal is projecting. · Usually the recommended setting is ON. DIRECT POWER ON You can switch the projector start up status for when the Mains lead is connected while the MAIN POWER is on, or for when the MAIN POWER is switched on while the Mains lead is connected. Press I H to select the required option. OFF The projector will start from the standby mode or the projecting mode. The projector will start from the projecting mode. INSTALLATION When installing the projector, select the projection method according to the projector position. See "Projection method" on page 17. FRONT/DESK FRONT/CEILING REAR/DESK REAR/CEILING Setting on a desk/floor and projecting from front Mounting in the ceiling and projecting from front Setting on a desk/floor and projecting from rear Mounting in the ceiling and projecting from rear ON NOTE: · When the projector is started from the projecting mode, pressing the POWER button procedure is skippable. ENGLISH - 37 Settings OPTION menu HIGHLAND If you use the projector at high elevation, the HIGHLAND setting need to be ON to set the fan speed high. Press I H to select the required option. OFF ON The fan speed is low. The fan speed is high. DETAILED SETUP You can perform more detailed setting in various items. OSD DESIGN You can change the background color of the menu. Press I H to select the required option. TYPE1 TYPE2 TYPE3 Semi transparent black Solid blue Semi transparent dark blue NOTE: · At 1 400 m (4 593 ft) above sea level, the setting must be ON. [. . . ] «LAMPE DE REMPLACEMENT» s'affiche S'allume en ROUGE. en haut à gauche de l'écran, et attend votre Plus de 3 000 heures réponse. Pour le supprimer immédiatement, appuyer sur n`importe quelle touche. REMARQUE: · Les durées indiquées, de 2800 et 3000 heures, sont des estimations basé sur certaines conditions et ne représentent en aucun cas des durées garanties. · Pour plus d'informations à propos des caractéristiques de l'Unité de la lampe, telles que la durée de garantie, se reporter aux instructions fournies avec l'Unité de la lampe. [. . . ]