User manual PANASONIC PT-F300NTU

[. . . ] Operating Instructions LCD Projector Commercial Use Model No. PT-F300NTU PT-F300U (PT-F300NTU) Before operating this product, please read the instructions carefully and save this manual for future use. TQBJ0279-1 ENGLISH Important Safety Notice Dear Panasonic Customer: The following information should be read and understood as it provides details, which will enable you to operate the projector in a manner which is both safe to you and your environment, and conforms to legal requirements regarding the use of projectors. Before connecting, operating or adjusting this projector, please read these instructions completely and save this booklet with the projector for future reference. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector. [. . . ] Output audio in standby mode. AUDIO IN SELECT You can switch the audio output method for COMPUTER1 IN, COMPUTER2 IN and DVI-D IN terminals. DVI COM. AUDIO IN 2 Output audio that is input to the COMPUTER AUDIO 2. AUDIO IN Output audio that is input to the AUDIO IN. COMPUTER1 COM. AUDIO IN 1 Output audio that is input to the COMPUTER AUDIO 1. AUDIO IN Output audio that is input to the AUDIO IN. ENGLISH - 42 PROJECTOR SETUP menu COMPUTER2 COM. AUDIO IN 2 Output audio that is input to the COMPUTER AUDIO 2. AUDIO IN Output audio that is input to the AUDIO IN. FILTER COUNTER RESET After you replaced the Auto Cleaning Filter (ACF), REMAINING FILTER of STATUS in PROJECTOR SETUP need to be reset to "0". Press the ENTER button for more than 3 seconds. The confirmation screen will be displayed. TEST PATTERN You can use the 7 different test patterns to adjust the focus of the image. See "Lens shift and positioning" on page 17. Press the ENTER button to display the test pattern 1. Press I H to select the required test pattern. Press the MENU or RETURN button to return to the previous menu, or press repeatedly to escape from the menu mode. 2. Select OK by pressing I, then press the ENTER button. Display the STATUS and confirm the figure. NOTE: · When the projector and/or the screen is tilted, adjust the focus at the center of the image. The upper and lower edge might be out of focus. · When the image is distorted in keystone, adjust the KEYSTONE in POSITION menu. INITIALIZE ALL You can reset all of the customized settings to the factory defaults except NETWORK, RUNTIME and REMAINING FILTER of STATUS in PROJECTOR SETUP menu. Select OK by pressing I, then press the ENTER button. Turn off the power by pressing the power button. Switch off the MAIN POWER button to reset the projector. The minimum required setting screen will be displayed. See "Minimum required setting screen" on page 11. NOTE: · The security system is deactivated by default and when initialized. · When the projector is initialized, it will be reset to the factory default password operation. ENGLISH - 43 Settings SECURITY menu Remote control Control panel PASSWORD CHANGE You can change the password operation to your original. Press a series of button operation up to 8 as a password by using F G I and H. Press the exact same series of button operation you entered in the NEW password box for confirmation. If a series of button operation is incorrect, you will be asked to perform again. See "Navigating through the menu" on page 32. See "Main menu and Sub-menu" on page 30. Entering the SECURITY menu Every time when you apply to the SECURITY menu, you will be asked to perform the password operation. PICTURE POSITION LANGUAGE DISPLAY OPTION PROJECTOR SETUP SECURITY NETWORK PASSWORD PASSWORD CHANGE TEXT DISPLAY TEXT CHANGE MENU LOCK MENU LOCK PASSWORD CONTROL DEVICE SETUP PASSWORD RETURN 4. Press the ENTER button. NOTE: · The entered password operations will appear as asterisks in the box. OFF OFF TEXT DISPLAY You can set your original text, such as company name or URL information, to display regularly at the bottom of the projected image while projecting. OFF ON Deactive Active OFF ENTER When you apply to the SECURITY menu before you change the password to your original, perform to input the following factory default password operation. Press F H G I F H G I and the ENTER button. TEXT CHANGE You can enter your original text up to 22 characters for TEXT DISPLAY. TEXT CHANGE After you change the password When you apply to the SECURITY menu after you change the password to your original in the PASSWORD CHANGE menu, input the original password operation. ALL DELETE Settings SPACE NOTE: · The factory default password is valid until you change the password in PASSWORD CHANGE menu. [. . . ] haut à gauche de l'écran, et attend votre réponse. Pour le supprimer immédiatement, appuyer sur n`importe quelle touche. Plus de 6000 heures REMARQUE: · Les durées indiquées, de 5000 et 6000 heures, sont des estimations basé sur certaines conditions et ne représentent en aucun cas des durées garanties. · Pour plus d'informations à propos des caractéristiques de l'unité de la lampe, telles que la durée de garantie, se reporter aux instructions fournies avec l'unité de la lampe. FRANÇAIS - 69 Information Importante Remplacement de l'unité de la lampe Remplacement de l'unité de la lampe Procédure de remplacement Retirer et remplacer la lampe 1. Dévisser à l'aide d'un tournevis cruciforme les 2 vis de fixation du couvercle de la lampe à l'arrière du projecteur jusqu'à ce qu'elles tournent librement, puis retirer le couvercle de la lampe. [. . . ]