User manual PANASONIC PT-L6500U

[. . . ] Model number: PT-LB50NTU / PT-L6500U / PT-LB50SU Serial number: IMPORTANT SAFETY NOTICE WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. Power Supply: This LCD Projector is designed to operate on 100 V ­ 240 V, 50 Hz/60 Hz AC, house current only. CAUTION: The AC power cord which is supplied with the projector as an accessory can only be used for power supplies up to 125 V, 7 A. If you need to use higher voltages or currents than this, you will need to obtain a separate 250 V power cord. [. . . ] B The ratio of length and width of an image may become incorrect depending on the amount of the keystone correction. B Keystone distortion of the onscreen display will not be corrected. BYou can correct the keystone distortion manually when "REALTIME KEYSTONE" is set to "ON". However, when you turn on the power, the amount of correction will be reset and "REALTIME KEYSTONE" will function again if the tilt is different from the last time you used the projector. If you correct the keystone distortion manually when "REALTIME KEYSTONE" is set to "OFF", the amount of correction will be stored by the projector even after the power is turned off. POSITION (S-VIDEO/VIDEO/RGB/YPBPR only) Moves the picture position. Press the ENTER button to display the "POSITION" screen. Press the I or H button to move the picture horizontally. Press the F or G button to move the picture vertically. DOT CLOCK (RGB only) Periodic striped pattern interference (noise) may occur when a striped pattern such as the one below is projected. If this happens, press the I or H button to adjust so that any such noise is minimised. CLOCK PHASE (RGB/YPBPR only) Adjust the "DOT CLOCK" setting first before carrying out this adjustment. Press the I or H button to adjust so that the noise level is least noticeable. NOTE: B If signals with a dot clock frequency of 100 MHz or higher are being input, interference may not be completely eliminated when the "DOT ENGLISH-45 Adjustments and settings CLOCK" and "CLOCK PHASE" adjustments are carried out. ASPECT (S-VIDEO/VIDEO/480i, 576i, 480p and 576p YPBPR only) S4:3 The size of the input signal is compressed to 75% and projected. SIMPLE Only the name of the input signal will be displayed. F G INPUT GUIDE STARTUP LOGO When the input signal is changed, the input signal information will be displayed in the upper right corner of the projected images. You can select the level of the input signal information. ON The "Panasonic" logo will be displayed when the power is turned on. OFF The "Panasonic" logo will not be displayed when the power is turned on. ENGLISH-49 Adjustments and settings NOTE: B If "INPUT GUIDE" is set to "DETAILED", the guide screen for computer connection will be displayed when PC1 or PC2 is selected and no signal is being input to the PC 1 IN or PC 2 IN connector. If you would like the guide screen not to be displayed, set "INPUT GUIDE" to "SIMPLE" or "OFF". POINTER SELECT LAMP POWER If you press the POINTER button on the remote control unit, the pointer will be displayed. You can select the pointer from 3 types as shown below (refer to page 35). A circle with a cross will be displayed. A hand will be displayed. This setting changes the lamp brightness. When set to "ECOMODE", the luminance of the lamp is reduced, but the projector uses less power, and the operating noise is also reduced. This can help to extend the lamp's operating life. If using the projector in small rooms where high luminance is not required, it is recommended that you set the "LAMP POWER" to "ECO-MODE". NOTE: B "LAMP POWER" cannot be set when no signal is being input. PC2 SELECT This setting is used to select the function of the PC 2 IN/PC 1 OUT connector. [. . . ] B Il faut utiliser un tournevis Phillips pour déposer le bloc de lampe. REMARQUE: B Le projecteur n'est pas fourni avec un bloc de lampe de rechange. Demander les détails au revendeur. Numéro de produit du bloc de lampe: ET-LAB50 ATTENTION: B Ne pas utiliser un bloc de lampe avec un numéro de pièce autre que celui indiqué ci-dessus. 80-FRANÇAIS Affichage à l'écran Indicateur LAMP Plus de 1 800 heures Plus de 2 000 heures Affiché pendant 30 secondes. [. . . ]