User manual PANASONIC PT-L785

[. . . ] Note that ® and TM marks are not indicated in the text of this manual. 2 Connecting a PC System requirements The following system specifications are required in order to use the networking functions. Hardware requirements OS: Windows XP/2000/Me (Millennium Edition)/98SE (Second Edition) CPU: Pentium III or faster or compatible processor (Celeron 633 MHz or faster is recommended) RAM: 64 MB or more (128 MB or more for Windows XP/2000) Hardware conditions: If you want to use the e-mail function, make sure the system can handle e-mail. Web browser: Internet Explorer 6. 0 or newer, Netscape Communicator 7. 0 or newer LAN cable Type: Category 5 compatible straight cable Length: 100 meters or less Note: Note that operation is not guaranteed when used with system environments other than the above or on homemade computers. Operation is not guaranteed for all computers that meet the above conditions. Connection example Projector Personal computer 10 BASE-T or 100 BASE-TX LAN cable (straight) Hub Note: Touching the LAN port with your hand (or body) when you are carrying a static charge may damage the equipment due to a discharge of static electricity. Therefore, be careful not to touch the LAN port or metal parts of the LAN cable. [. . . ] Use the following procedure to change the password. This procedure sets the password which is entered on page 6. Select this parameter to set the password to be entered when WEB the projector is accessed through a web browser, then press PASSWORD the [ENTER] button. Use the [ ] buttons to select alphanumeric characters (up to 16 characters), then press the [ENTER] button. Select [OK], then press the [ENTER] button. MAC ADDRESS A MAC address (Media Access Control Address) which is unique to the network equipment is displayed here. The MAC address may be needed when, for example, a DHCP server is used. 4 Network status screen 1 Select [NETWORK] on the screen discussed on the preceding page, then press the [ENTER] button. ] buttons 2 Use the [ then changeto select a parameter, its setting. NETWORK ID DHCP IP ADDRESS SUBNET MASK GATEWAY ENTER LAN1 OFF ON 192. 168. 0. 8 255. 255. 255. 0 192. 168. 0. 254 ESC SELECT : [ ] [ ] ENTER : [ENTER] ESC : [MENU] Parameter ID Description IDs are identification numbers under which settings are stored. Three different IDs can be stored (LAN1 through LAN3). Use the [ ] buttons to toggle this setting ON/OFF. ON: Select this setting to automatically acquire an IP address using a DHCP server. OFF: Select this setting if you are not using a DHCP server. Enter settings in these parameters if you are not using a DHCP server. Select a parameter, then press the [ENTER] button. Use the [ ] buttons to select numbers and periods, then press the [ENTER] button. Select [OK], then press the [ENTER] button. DHCP IP ADDRESS SUBNET MASK GATEWAY Notes: · If you are using a DHCP server, make sure it is on and ready. · IP address, subnet mask, and gateway settings should be obtained from your network administrator. 5 Using Web Browser Control Access procedure web PC, then 1 Start thewhichbrowser on yourprojector. enter the IP address was set in the in the user name 2 Enter "user1"the password field. field, then enter the password in The default setting is "panasonic" (all lower case). If you have changed the password, enter the new password here. If you forget your password, set a new password using the procedure described on page 4. [. . . ] Click [Projector Control], then [E-mail set up] to display the E-mail setup page. E-mail Enable/Disable toggling SMTP server field Sender field (alphanumeric characters) Memo field (alphanumeric characters) Minimum sending interval field (applies only to temperature warnings) Set temperature selection (38 °C/100 °F, 40 °C/104 °F, 42 °C/108 °F and 44 °C/111 °F) 12 Button to update settings ON/OFF toggling for permission to send e-mail when error occurs Destination e-mail address field Change lamp usage time set value ON/OFF toggling for permission to send e-mail based on lamp usage time ON/OFF toggling for permission to send email based on air intake sensor temperature Periodic warning interval setting (e-mail is sent on the checked days of the week/times) The settings for e-mail address 1 are the same. 13 Using Web Browser Control (continued) DNS server setup page Click [Network Setting], then [DNS Server set up] to display the DNS Server Setup page. Primary DNS server address Available input characters: Numbers (0 - 9), period (. ) (ex. . ) Secondary DNS server address Available input characters: Numbers (0 - 9), period (. ) (ex. ) Button to update settings 14 POP server setup page Click [Network Setting], then [POP server set up] to display the POP Server Setup page. Toggling between Enabling/Disabling POP before SMTP POP server name field Available input characters: Alphanumeric characters (A­Z, a­z, 0­9), hyphen (-), period (. ) POP server user name field POP server password field Button to update settings 15 Using Web Browser Control (continued) Adjust clock page Click [Network Setting], then [Adjust clock] to display the Adjust clock page. Time zone selection Button to update time zone setting New date field New time field Button to update time and date settings Note: If the time becomes incorrect immediately after setting the correct time, then the battery needs to be changed. Contact the dealer where you bought the projector to have the battery changed. 16 Network status page Click [Network Setting], then [Network status] to display the Network status page. MAC address display Set subnet mask display Set IP address display Network software version display Network status display 17 Using Web Browser Control (continued) Password change page This page can be used to change the password entered on page 6. [. . . ]