User manual PANASONIC PT-L785U

[. . . ] R LCD Projector Commercial Use Operating Instructions Model No. PT-L785U RGB VIDEO A ALL SET Before operating this product, please read the instructions carefully and save this manual for future use. TQBJ 0150 ENGLISH Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector. The serial number of your product may be found on its bottom. You should note it in the space provided below and retain this booklet in case service is required. [. . . ] Set to "ON" pressing the I or H button to turn off the volume of the sound output. To cancel muting, set to "OFF". ON SELECT:[^][@] ADJUST:[{][}] ENTER:[ENTER] ESC:[MENU] Changing the display language Press the F, G, I and H buttons on the projector or remote control unit to select a language, then press the ENTER button to accept the setting. LANGUAGE ENGLISH DEUTSCH FRANÇAIS ESPAÑOL ITALIANO SELECT:[^][@][{][}] SELECT:[{][}] ESC:[MENU] ENTER:[ENTER] 46-ENGLISH Option settings Press the F or G button on the projector or remote control unit to select an item, then press the I or H button to change the setting. OPTION OSD AUTO SEARCH AUTO SIGNAL RGB2 SELECT RGB/YPBPR VGA60/480p BACK COLOR CINEMA REALITY NEXT PAGE @ SELECT:[^][@] ADJUST:[{][}] OFF OFF OFF INPUT RGB VGA60 BLUE OFF ON ON ON OUTPUT YPBPR 480p BLACK ON AUTO SEARCH ON The input signal will be detected and selected automatically when the input select (RGB, VIDEO) buttons are pressed for a few seconds. (page 14) OFF "AUTO SEARCH" is disabled. NOTE: B "AUTO SEARCH" will not function when the input signal is being projected. ESC:[MENU] AUTO SIGNAL This should normally be set to "ON". ON "AUTO SETUP" will be carried out automatically when the input signal is changed. OFF "AUTO SETUP" will not function when the input signal is changed. RGB2 SELECT SELECT:[^][@] ADJUST:[{][}] ENTER:[ENTER] ESC:[MENU] OSD ON The signal name is displayed in the top-right corner of the screen when the input signal is changed. OFF Use this setting when you do not want the signal name to be displayed. NOTE: B The setting for "TV-SYSTEM" will also be displayed when an S-VIDEO/VIDEO signal is being input. This setting is used to select the function of the RGB2 IN/RGB OUT connector. When set to "OUTPUT", the selected input signal (RGB1 or RGB3) will be output. RGB/YPBPR This setting is valid when 480i, 576i, 480p, 576p, 1 080/60i, 1 080/50i and 720/60p signals are being input. Select the setting in accordance with the input signal. "RGB/YPBPR" is displayed when the RGB1 IN, RGB2 IN or RGB3 IN connector has a signal being input. ENGLISH-47 Adjustments and settings OPTION PREVIOUS PAGE ^ FRONT/REAR DESK/CEILING FAN CONTROL LAMP POWER LAMP RUN TIME FUNC1 CONTROL KEY SET ID AUTO POWER OFF FRONT DESK STANDARD LOW REAR CEILING HIGH HIGH 10 H MUTE KEYSTONE OFF ON ALL DISABLE VGA60/480p Set to "VGA60" when 59. 9Hz VGA480 signals are being input (refer to page 70 for details). Set to "480p" when 480p RGB signals are being input. BACK COLOR This sets the color which is projected onto the screen when no signal is being input to the projector. DESK When the projector is placed on a desk or similar. CEILING When the projector is suspended from a ceiling using the ceiling bracket (sold separately). FAN CONTROL Set "FAN CONTROL" to "HIGH", when using this projector at high elevations (above 1 400 m) only. CINEMA REALITY (S-VIDEO/VIDEO/480i and 576i YPBPR only) ON Set to "ON" when you would like 24 frames per second pictures (such as movies) to project the source faithfully. OFF Set to "OFF" when the projected pictures have problems with captions or subtitles when the setting is "ON". LAMP POWER This setting changes the lamp brightness. When set to "LOW", the luminance of the lamp is reduced, but the projector uses less power, and the operating noise is also reduced. This can help to extend the lamp's operating life. If using the projector in small rooms where high luminance is not required, it is recommended that you set the "LAMP POWER" to "LOW". FRONT/REAR This setting should be changed in accordance with the projector setting-up method. (Refer to page 18. ) FRONT When the projector is placed in front of a screen. REAR When using a translucent screen. LAMP RUN TIME This setting displays the usage time for the lamp unit which is currently being used. When replacing the lamp unit, follow the instructions on page 58, and reset "LAMP RUN TIME" to "0". NOTE: B The lamp's operating life varies depending on the usage conditions (such as the "LAMP POWER" setting and the number of times the power is turned on and off). DESK/CEILING This setting should be changed in accordance with the projector setting-up method. (Refer to page 18. ) 48-ENGLISH FUNC 1 This assigns a function to the FUNC1 button of the remote control unit . [. . . ] B Il faut utiliser un tournevis Phillips pour déposer le bloc de lampe. REMARQUE: B Le projecteur n'est pas fourni avec un bloc de lampe de rechange. Demander les détails au revendeur. Numéro de produit du bloc de lampe: ET-LA785 ATTENTION: B Ne pas utiliser un bloc de lampe avec un numéro de pièce autre que celui indiqué ci-dessus. 84-FRANÇAIS Affichage à l'écran Indicateur LAMP Plus de 1 350 heures Plus de 1 500 heures Affiché pendant 30 secondes. [. . . ]