User manual PANASONIC PT-LB90NTU WIRELESS FUNCTION EDITION WINDOWS

[. . . ] Operating Instructions LCD Projector Model No. Commercial Use PT-LB90NTU PT-LB90U PT-LB78VU PT-LB75VU Thank you for purchasing a Panasonic Projector. J Before operating this product, please read the instructions carefully, and save this manual for future use. Before using your projector, be sure to read "Precautions with regard to safety" (pages 6 - 10). TQBJ0302 ENGLISH Important Safety Important Safety Notice Notice Dear Panasonic Customer: The following information should be read and understood as it provides details, which will enable you to operate the projector in a manner which is both safe to you and your environment, and conforms to legal requirements regarding the use of projectors. Before connecting, operating or adjusting this projector, please read these instructions completely and save this booklet with the projector for future reference. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector. [. . . ] See "List of compatible signals". (Æpage 52) 32 - ENGLISH POSITION menu OVER SCAN Use this function when characters or pictures are cropped near the periphery of the projected image. (Available with signals of S-VIDEO/VIDEO/RGB (Moving image)/YPBPR only) Zoom out z Setting range: 0 to +3 J 16:9 When a standard signal *1 is input, it is projected in 16:9 aspect ratio. When a wide signal *2 is input, it is projected in the current input aspect ratio. z Input signal: 1 080/60i Zoom in Remarks z OVER SCAN is not available when network signals are input. Image: Panel: J H FIT When a standard signal *1 is input, it is projected without changing the aspect ratio, using all the panel pixels in the horizontal direction and cropping the top and bottom of the image. z Input signal: SXGA ASPECT You can switch the aspect ratio manually when needed. Selectable options vary according to input signal. Change setting AUTO THROUGH S4:3 Remarks z AUTO mode is displayed only when NTSC 480i z THROUGH mode is displayed only for certain Change setting 4:3 16:9 H FIT HV FIT V FIT Image: J V FIT When a wide signal *2 is input, it is projected without changing the aspect ratio, using all the panel pixels in the vertical direction and cropping the right and left of the image. z Input signal: 1 080/60i signal is input. J AUTO (Available with signal of NTSC 480i only) The signal which contains an identifying signal will be detected and will automatically project the image in the most optimal aspect ratio. Image: J HV FIT The image is projected all over the panel pixels (screen). The input signal is projected at the aspect ratio of the panel (screen). z Input signal: 1 080/60i J 4:3 When a standard signal *1 is input, it is projected in 4:3 aspect ratio. z Input signal: XGA Image: Image: *1: A standard signal has an aspect ratio of 4:3 or 5:4. *2: A wide signal has an aspect ratio of 16:10, 16:9 or 15:9. ENGLISH - 33 Settings signals. z For the wide signal *2, the aspect ratio cycles through 16:9 V FIT HV FIT. POSITION menu J S4:3 When a standard signal *1 is input, the input signal will be sized down 75% and projected. S4:3 mode is effective when projecting 4:3 image onto a 16:9 screen. z Input signal: XGA FRAME LOCK If the projected image is degraded, you can activate FRAME LOCK for synchronisation. (Available with signals of RGB only) Change setting ON OFF Active Deactive Change setting Image: Panel: Screen: J THROUGH The image will be projected without any size adjustment. z Input signal: NTSC Image: Panel: *1: A standard signal has an aspect ratio of 4:3 or 5:4. Note z If you project a 4:3 image onto a 16:9 screen, the image may distort or some portions may be cropped. Select an aspect ratio (4:3) which preserves the intention of the image creator. Remarks z The order of ASPECT types is defined not only by the input method but also by the input signals. z If you project a copyrighted image enlarged or distorted by using ASPECT function in commercial use in a public place, such as a restaurant or hotel, you might infringe on the copyright of the creator which is protected by copyright law. Settings 34 - ENGLISH LANGUAGE menu Navigating through the MENU (Æpage 27), select LANGUAGE from the main menu and then display the sub-menu. z Select the required language withbuttons LANGUAGE menu and press the ENTER button to set. Remote control Control panel PICTURE POSITION LANGUAGE DISPLAY OPTION PROJECTOR SETUP SECURITY NETWORK PICTURE POSITION LANGUAGE DISPLAY OPTION PROJECTOR SETUP SECURITY NETWORK The set language is highlighted. ENGLISH - 35 Settings DISPLAY OPTION menu DISPLAY OPTION menu Navigating through the MENU (Æpage 27), select DISPLAY OPTION from the main menu and then select the required item from the sub-menu. Remote control Control panel Remarks z The key commands are depending on the manufacturers. Please refer to the instructions which were provided with the computers for more detailed information. You can change the background of the on-screen menu (OSD). TYPE1 TYPE2 TYPE3 Semi transparent black Solid blue Semi transparent dark blue J OSD DESIGN J WARNING MESSAGE ON-SCREEN DISPLAY You can set the on-screen display. Change setting Change setting You can choose to display or not to display the warning massages. ON OFF Warning messages will be displayed No display J INPUT GUIDE When you change the input method, the guidance appears in the upper right corner of the screen. The following display methods are available. [. . . ] Préparer un tournevis cruciforme. Lors du remplacement de l'unité de la lampe, veillez à la tenir par la poignée. Tenez l'unité de la lampe horizontalement pour éviter que les pièces cassées ne se répandent. En cas d'installation du projecteur au plafond, ne jamais travailler directement dessous et éloigner le visage du projecteur, sortir la lampe horizontalement. Remarque z Avant de remplacer la lampe, la laisser refroidir pour éviter les risques de brûlures, les dommages et autres dangers. [. . . ]